background image

59 

 

Immunity test 

IEC 60601 test level 

Compliance level 

Electromagnetic environment 

guidance 

Radiated RF IEC 61000-

4-3 

385 MHz 27 V/m 

450 MHz 28 V/m 

710 MHz 9 V/m 

745 MHz 9 V/m 

780 MHz 9 V/m 

810 MHz 28 V/m 

870 MHz 28 V/m 

930 MHz 28 V/m 

1720 MHz 

28 V/m 

1845 MHz 

28 V/m 

1970 MHz 

28 V/m 

2450 MHz 

28 V/m 

5240 MHz 

9 V/m 

5500 MHz 

9 V/m 

5785 MHz 

9 V/m 

385 MHz 27 V/m 

450 MHz 28 V/m 

710 MHz 9 V/m 

745 MHz 9 V/m 

780 MHz 9 V/m 

810 MHz 28 V/m 

870 MHz 28 V/m 

930 MHz 28 V/m 

1720 MHz 

28 V/m 

1845 MHz 

28 V/m 

1970 MHz 

28 V/m 

2450 MHz 

28 V/m 

5240 MHz 

9 V/m 

5500 MHz 

9 V/m 

5785 MHz 

9 V/m 

The FeNObreath™ Monitor is 

suitable for the electromagnetic 

environment of typical 

commercial or hospital settings. 

 

Summary of the clinical data 

Study 1: A clinical Precision study comparing intra and inter usability of FeNO measurement using 
the FeNObreath™. 

In one of the studies conducted, the clinical precision, as it relates to user bias of the FeNObreath™, 
was evaluated in a mixed study population of 76 participants - including 24 pediatric participants 
(ages 7-17 years) and 52 adults (18 years+). Participants were asked to obtain 2 FeNObreath™ 
measurements with the assistance of 3 health care professionals (HCPs), for a total of 6 
FeNObreath™ evaluations per participant. 

The clinical precision study was designed to capture the accuracy and precision of the FeNObreath™ 
device, therefore FeNO values acquired by subjects covered potential FeNO values which would be 
observed in clinical practice. The within subject precision* was assessed from this study population 
and is presented in the table below: 

Median 

Concentrations 

Within Subject 

Mean SD (ppb) 

Within Subject 

Mean CV (%) 

95% CI for CV (%) 

0 to <10 

10 

0.8034172 

13.35% 

7.85%; 18.85% 

10 to <20 

21 

1.2430966 

9.18% 

6.73%; 11.64% 

20 to <30 

23 

0.9720727 

4.17% 

2.48%; 5.85% 

30 to <40 

1.2279205 

3.65% 

1.3%; 6% 

40 to <50 

1.3867462 

3.17% 

0.23%; 6.1% 

>=50 

12 

1.4078969 

1.89% 

1.29%; 2.48% 

Summary of Contents for FENObreath


































































Reviews: