background image

Product description

EL2904

18

Version: 2.3.0

3.3

Technical data

Product designation

EL2904

Number of outputs

4

Status display

4 (one green LED per output)

Fault reaction time

≤ watchdog times

Output current per channel

max. 500 mA, min. 20 mA with 

Current Measurement Active 

pa-

rameter enabled

Utilization category according to EN 60947-5-1

DC-13

Intended load

Pilot Duty

Actuators

When selecting actuators please ensure that the EL2904 test
pulses do not lead to actuator switching.

Cable length between actuator and terminal

unshielded max. 100 m
shielded max. 100 m

Wire cross-section

min. 0.75 mm

2

Input process image

6 bytes

Output process image

6 bytes

EL2904 supply voltage (PELV)

24 V

DC

 (–15% / +20%)

(A 10 A fuse should be provided for the potential group)

Protection class

III

(by using a SELV/PELV power supply unit)

Overvoltage category

II

Current consumption via E-bus

approx. 221 mA

Power dissipation of the terminal

typically 2 W

Electrical isolation (between the channels)

no

Electrical isolation (between the channels and the E-bus)

yes

Insulation voltage (between the channels and the E-bus, under com-
mon operating conditions)

Insulation tested with 500 V

DC

Dimensions (W x H x D)

24 mm x 100 mm x 68 mm

Weight

approx. 100 g

Permissible ambient temperature (operation) 
up to SW 03

0°C to +55°C (see notes in chapter Example configuration for
temperature measurement)

Permissible ambient temperature (operation) 
from SW 04 (CW 02/2014)

-25°C to +55°C (see notes in section Example configuration for
temperature measurement)

Permissible ambient temperature (transport/storage)

-40 °C to +70 °C

Permissible air humidity

5% to 95%, non-condensing

Permissible air pressure (operation/storage/transport)

750 hPa to 1100 hPa

(this corresponds to an altitude of approx. -690 m to 2450 m
above sea level, assuming an international standard atmos-
phere)

Climate category according to EN 60721-3-3

3K3 
(the deviation from 3K3 is possible only with optimal environmen-
tal conditions and also applies only to the technical data which
are specified differently in this documentation)

Permissible pollution degree 
according to EN 60664-1

2
(note chapter 

Maintenance [

}

 44]

)

Inadmissible operating conditions

TwinSAFE Terminals must not be used under the following oper-
ating conditions:

• under the influence of ionizing radiation (exceeding the

natural background radiation)

• in corrosive environments

• in an environment that leads to unacceptable soiling of

the Bus Terminal

EMC immunity / emission

conforms to EN 61000-6-2 / EN 61000-6-4

Vibration / shock resistance

conforms to EN 60068-2-6 / EN 60068-2-27

Shocks

15 g with pulse duration 11 ms in all three axes

Protection class

IP20

Equipment type according to EN 61010-2-201

Open equipment

Permitted operating environment

In the control cabinet or terminal box, with minimum protection
class IP54 according to IEC 60529

Correct installation position

see chapter Installation position and minimum distances

Approvals

CE, cULus, ATEX, TÜV SÜD

Summary of Contents for EL2904




















































Reviews: