manualshive.com logo in svg

Beckhoff EK1122, Documentation

Share
Download
Beckhoff EK1122 Documentation Download Page 46

Mounting and wiring

EK1122, EK15xx

46

Version: 3.4

5.4

Mounting and demounting - terminals with front
unlocking

The terminal modules are fastened to the assembly surface with the aid of a 35 mm mounting rail (e.g.
mounting rail TH 35-15).

Fixing of mounting rails

The locking mechanism of the terminals and couplers extends to the profile of the mounting rail. At
the installation, the locking mechanism of the components must not come into conflict with the fixing
bolts of the mounting rail. To mount the recommended mounting rails under the terminals and cou-
plers, you should use flat mounting connections (e.g. countersunk screws or blind rivets).

 WARNING

Risk of electric shock and damage of device!

Bring the bus terminal system into a safe, powered down state before starting installation, disassembly or
wiring of the Bus Terminals!

Mounting

• Fit the mounting rail to the planned assembly location.

 

and press (1) the terminal module against the mounting rail until it latches in place on the mounting
rail (2).

• Attach the cables.

Demounting

• Remove all the cables.

• Lever the unlatching hook back with thumb and forefinger (3). An internal mechanism pulls the two

latching lugs (3a) from the top hat rail back into the terminal module.

Summary of Contents for EK1122





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands