Programmable Settings
How to Enter Programming Mode
After entering programming mode the LED will blink to indicate the current setting selection.
Pressing the Selector Button each time will cycle through the selections. After selecting the
desired setting, press and hold the button for at least 3 seconds to exit programming mode.
Turning ignition to OFF without pressing and holding the button for at least 3 seconds to exit
programming mode will result in the device returning to its previous setting.
Front Camera Auto Turn-On
At low speeds less than 15km/h, the Front Camera can be automatically displayed to assist in parking
and obstacle avoidance.
1. Press and hold the Selector Button then turn the ignition from OFF to ACC.
2. Keep the button depressed for at least 4 seconds to observe the LED change from Off -> Flashing.
3. Release the button to enter Front Camera Auto Turn On programming mode.
4. Press and release the button to change the setting. The LED will flash twice per cycle to indicate this
option has been enabled. Press and release the button again and the LED will flash once per cycle to
indicate this option has been disabled.
5. After selecting the desired setting, press and hold the Selector Button for at least 3 seconds to exit
programming mode.
LED Flash
1 Flash
2 Flashes
Front Camera Auto Turn-On
Disabled (default setting)
Enabled
Camera Display Timer
Sets the duration for the Front Camera and Backup Camera to be displayed when the Selector Button is
pressed. Users may also disable the timer for push on / push off activation only.
1. Press and hold the Selector Button then turn the ignition from OFF to ACC.
2. Keep the button depressed for at least 10 seconds but no more than 15 seconds to observe the LED
change from Off -> Flashing -> ON.
3. Release the button to enter Camera Display Timer programming mode.
4. Press and release the button to cycle through each of the 5 timer settings. The LED will flash to
indicate the current timer setting as shown in the table below:
5. After selecting the desired setting, press and hold the Selector Button for at least 3 seconds to exit
programming mode.
0 ~ 4 sec.
4 ~ 10 sec.
10 ~ 15 sec.
Over 15 sec.
No Effect
Front Camera Auto Turn-On
Camera Display Timer
Backup Camera PTV
OFF
Blinking
ON
Rapid Flashing
Selector Button Press & Hold Duration
LED Status
Programming Mode
LED Flash
Timer Duration
Timer Disabled (push on / push off)
*** Backup Camera will always display when reverse gear is engaged for either mode ***
LED Flash
1 Flash
2 Flashes
Backup Camera PTV
Disabled
Enabled (default setting)
Press and hold the Selector Button then turn the ignition from OFF to ACC.
● Keeping the button pressed continuously for at least 4 seconds but no more than 10 seconds
will result in the LED changing from OFF ->
Flashing
. Release the button while the LED is
Flashing
to enter the
Front Camera Auto Turn-On
Programming Mode.
● Keeping the button pressed continuously for at least 10 seconds but no more than 15
seconds will result in the LED changing from OFF ->
Flashing
->
ON
. Release the button
while the LED is
ON
to enter the
Camera Display Timer
Programming Mode.
● Keeping the button pressed continuously for more than 15 seconds will result in the LED
changing rom OFF ->
Flashing
->
ON
->
Rapid Flashing
. Release the button while the LED
is
Rapid Flashing
to enter the
Backup Camera PTV
Programming Mode.
Backup Camera PTV
The CS6EP features Backup Camera Push to View (PTV) Mode that displays the Backup Camera at
any time without the need to select reverse gear. Pressing the Selector Button once will display the
Front Camera. Pressing the Selector Button a second time will display the Backup Camera. Pressing
the Selector Button a third time will return to the normal screen.
Backup Camera PTV Mode can be disabled so that pressing the Selector Button a second time will
instead return to the normal screen. Backup Camera will always display when reverse gear is selected
regardless if Backup Camera PTV is enabled or disabled.
1. Press and hold the Selector Button then turn the ignition from OFF to ACC.
2. Keep the button depressed for at least 15 seconds to observe the LED change from Off -> Flashing
-> ON -> Rapid Flashing
3. Release the button to enter Backup Camera PTV programming mode.
4. Press and release the button to change the setting. The LED will flash once per cycle to indicate this
option has been disabled. Press and release the button again and the LED will flash twice per cycle to
indicate this option has been enabled.
5. After selecting the desired setting, press and hold the Selector Button for at least 3 seconds to exit
programming mode.
●
Default Setting - Backup Camera PTV Enabled
●
Optional Setting - Backup Camera PTV Disabled
● Enabling Front Camera Auto Turn-On may result in front camera briefly displaying when ignition
isturned ON.
Notes
Shifting into then out of reverse gear with Front or Backup Camera currently selected:
● With both Timer Duration disabled and Front Camera Auto Turn-On disabled, display will return to the
previously selected camera view when the gear shift is moved out of reverse.
● With Timer Duration not disabled (i.e. Timer Duration of 5 ~ 20 sec.), display will return to the normal
screen when the gear shift is moved out of reverse regardless of previous camera selection.
Notes
5 sec.
10 sec.
15 sec. (default setting)
20 sec.
1 Flash
2 Flashes
3 Flashes
4 Flashes
5 Flashes
Notes
Pressing the Selector Button each time will cycle the camera selection as shown below:
Pressing the Selector Button each time will cycle the camera selection as shown below:
Normal
Screen
Front
Camera
Backup
Camera
Normal
Screen
Front
Camera
1st Press
2nd Press
3rd Press
1st Press
2nd Press
