BeamMed Sunlight Omnisense 7000S User Manual Download Page 75 | Manualshive

Page: 75 / 284

background image

Omnisense 7000S/8000S

4-11

Measurement Accessories

4.4 Measurement Accessories

The photograph below shows a “phantom”. The phantom is
constructed of Perspex material which has known, stable SOS
behavior. It is used to verify that Omnisense is measuring speed
of sound accurately. The procedure is described in Chapter 6,
"System Quality Verification‚" page 6-1.

Figure 4.6

Phantom for system quality verification

A hand rest is provided with Omnisense for use in positioning a
patient’s arm correctly for a SOS measurement of the distal 1/3
radius. The hand rest is illustrated in the photograph below.

Figure 4.7

Limb positioning fixtures

SOS measurements of the distal radius are taken at about the
midpoint of the limb, while measurements of the phalanx and
metatarsal are located along the respective bones. To aid in
finding the correct location, Omnisense is shipped with one or

The phantom has an
LCD temperature gauge
on one side, and a con-
version table on the
other.

The hand rest supports
the lateral edge of the
outstretched palm when
scanning the radius.

«
...
73
74
75
76
77
...
»

Summary of Contents for Sunlight Omnisense 7000S





























































































































































































































































































Reviews:

No comments

Related manuals for Sunlight Omnisense 7000S

Brand: Facsimile Pages: 16

Brand: Facnor Pages: 33

Brand: Abus Pages: 2

Brand: Abus Pages: 12

Brand: Abu Garcia Pages: 6

Brand: Bard Pages: 144

Brand: GALBIATI Pages: 8

Brand: Vahva Jussi Pages: 9

Brand: BARKO LOADERS Pages: 85

Brand: Gebhardt Anlagentechnik Pages: 152

Brand: Hach Pages: 58

Brand: Hach Pages: 52

DISHSTAR ADA-SEER

Brand: Jackson Pages: 2

Brand: Jasco Pages: 2

Brand: Nektar Pages: 12

Brand: Vaillant Pages: 76

Brand: H2flow Pages: 2

Brand: V-TAC Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands