Beam Shout ts User Manual Download Page 36

Page: 36 / 42

SHOUT ts User’s Manual Version 1.0.1

Appendix A: PMS Features

The ts is capable of sending position reports in PECOS Message Structure (PMS).

PMS complies with the Blue Force Tracking Data Format Specification as defined

in the document PECOS 200907-001 Version 1.7. The ts is shipped without PMS

features activated and can only be enabled by NAL Research at the request of an

authorized user. When PMS is enabled, the Format menu has an additional option

called PECOS as shown in the figure below.

With PMS enabled, user has the option to select any one of sixteen Brevity Codes

(0000 through 1111) to be included in the PMS tracking reports. These codes are

represented by A(z), B, C(z) and D and can be selected via the touchscreen. Each

code will light up as a green dot inside the Brevity icon when selected.

RACKING

  Iridium
  GPS
01-Nov-11                         8:00 AM

Format

o Full, 30 bytes

o Position Only, 10 bytes

o PECOS

Brevity

Iridium

GPS
01-Nov-11 8:00 AM

Tracking

On/Off Rpt Rate Format Brevity

Cancel 911 Stats

Summary of Contents for Shout ts











































Search results

Summary of Contents for Shout ts

Reviews:

Related manuals for Shout ts

Brands by name

Popular brands

Beam Shout ts, User Manual

Search results

Summary of Contents for Shout ts

Reviews:

Related manuals for Shout ts

Brands by name

Popular brands