5/8
Note:
All parameters or functions listed in the following tables are only accessible if the sensor is in adjustment session. The red LED flashes slowly.
During an adjustment session each parameter may be checked or changed at any time in the following way :
PARAMETERS
OPERATIONS
CHECK
VALUES
Press the key corresponding to the parameter to be checked and then press the
CHECK VALUES
key (15).
The number of times the LED flashes corresponds to the value of the checked parameter. No LED flash corresponds to the value 0.
Repeat this operation to check the value of the other parameters if required.
Example:
SENSITIVITY
key (7) – 7 flashes of the LED: the radar sensitivity is set at the value 7.
CHECK VALUES
:
PLUS
Press the key corresponding to the sensitivity (7) or holdtime (6) parameter to be modified and then press the
PLUS
key (3) to increase the
value by 1 unit.
PLUS
:
MINUS
Press the key corresponding to the sensitivity (7) or holdtime (6) parameter to be modified and then press the
MINUS
key (5) to reduce the
value by 1 unit.
MINUS
:
Note about LED signal: The red LED flashes quickly waiting for the value. Once this has been entered, it flashes slowly again.
PARAMETERS
OPERATIONS
DEFINITIONS - ADVICES
SENSITIVITY
Press the
SENSITIVITY
key (7).
Use the
NUMBER
keys
0-9
(1) to enter the required sensitivity (or adjust this
parameter using the
PLUS
(3) or
MINUS
(5) keys as explained above)
SENSITIVITY :
To increase the
sensitivity
means to increase the sensor
capabilities to detect small useful signals. Practically, to
increase the sensitivity leads to increase the dimensions of the
sensing field.
HOLD TIME
Press the
HOLD TIME
key (6).
Use the
NUMBER
keys
0-9
(1) to enter the required hold time (0.5 s to 9 s)
(or adjust this parameter using the
PLUS
(3) or
MINUS
(5) keys as explained
above).
HOLD TIME
:
The
hold time
allows extended output activation time after a
motion detection has stopped. It is recommended to use this
parameter instead of the operator’s one with the same function
(interferences with the sensor). In X-MTF mode, the hold time
defines the minimum required time during which no motion has
to be "seen" by the sensor to release the detection.
X-MTF
SENSITIVITY
Press the
X-MTF
SENSITIVITY
key (12).
Use the
NUMBER
keys
0-9
(1) to enter the required sensitivity.
0 = X-MTF OFF
X-MTF SENSITIVITY :
The sensor switches to X-MTF mode after a motion detection
occurs (if X-MTF-Sensitivity is set to a value higher than 0).
The sensor remains in X-MTF mode as long as a motion (even
very small movements) is ‘seen’ by the sensor in any direction.
Increasing this parameter increases the ability of the sensor to
detect very small useful signals. Note: a higher X-MTF
sensitivity increases the detection zone!
DETECTION
MODE
Press the
DETECTION MODE
key (8).
Use the
NUMBER
keys
1-5
(1) to select the required mode :
Key 1
: Bidirectional mode
Key 2
: Unidirectional mode
Key 3
: Unidirectional mode with MTF-function
Key 4
: Unidirectional mode reverse
Key 5
: Unidirectional mode reverse with MTF- function
DETECTION MODE :
With the
bidirectional mode
, the approaching and departing
target is detected. With the
unidirectional
mode, only the
approaching
target is detected. With the
unidirectional
mode
reverse
, only the
departing
target is detected.
Using the
MTF (Motion Tracking Feature)
enables the sensor
to automatically switch from the unidirectional mode to
bidirectional mode as soon as a target is detected. This
function is recommended for applications with elderly people
or anyone approaching the door hesitantly.
IMMUNITY
Press the
IMMUNITY
key (9).
Use the
NUMBER
keys
1-9
(1) to select the
required mode:
Key 1
: Low immunity
Key 2
: Normal
Key 3
: Increased immunity
IMMUNITY :
To
increase the immunity
means to strengthen the
resistance to external disturbances such as
rain, vibrations
,
etc.
MOUNTING
HEIGHT
Press the
MOUNTING HEIGHT
key (13),
Use the
NUMBER
keys
1-2
(1) to select the required mounting height :
Key 1
: Standard mounting height
Key
2
: High mounting height
MOUNTING HEIGHT
:
The sensor presents an increased sensitivity scale in
high
mounting mode
. This setting is recommended when the
detection on the field limits is erratic.
Attention
: the high mounting mode can only be used in
appropriate areas.
OUTPUT
CONFIGURA-
TION
Press the
OUTPUT CONFIGURATION
key (17).
Use the NUMBER keys
1-2
(1) to select the required output configuration :
Key 1
: Active mode
Key 2
: Passive mode
OUTPUT CONFIGURATION
:
Active
Passive
Detection
No Detection
DOOR
CONTROL
Press the
DOOR CONTROL
key (14),
Use the NUMBER keys
1-3
(1) to select the required door control:
Key 1
: Automatic mode
Key 2
: Door permanently open
Key 3
: Door permanently closed
DOOR CONTROL:
In ‘’door permanently open’’ mode, the sensor is continuously
detecting. The red LED is continuously ON.
In ‘’door permanently closed’’ mode, the sensor is in standby.
It detects nothing anymore and the LED is continuously OFF.
