BDS MAB 455 Original Operating Instructions Download Page 3

3

MAB 455

GB

Table of Contents

General instructions   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .3
Safety   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .5
Components / delivery contents   .  .  .  .  .10

Before using for the first time

   .  .  .  .  .  .  .11

Preparation .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .11
Using  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .14
Eliminating blockages .  .  .  .  .  .  .  .  .  .  .  .  .  .16
Cleaning/maintenance    .  .  .  .  .  .  .  .  .  .  .  .  .17
Storage   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .18
Troubleshooting    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .18
Technical data   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .19
EC Declaration of Conformity    .  .  .  .  .  .  .20

Dear Customer,
Before using the machine, please read the 

operating instructions contained in these 

operating instructions on startup, safety, 

intended use as well as cleaning and care.
The links and illustrations in these instruc-

tions refer to the illustrations on the inside 

of the cover.
Keep these operating instructions for later 

use and pass them onto the next owner of 

the machine.

General instructions

Copyright

This document is subject to copyright. Du-

plication or reprinting, even in part as well 

as reproduction of the illustrations, even 

if modified, is only permitted with written 

consent of the manufacturer.

Liability disclaimer

All technical information, data and in-

structions contained in these operating 

instructions for startup, operation and care 

correspond to the latest requirements at the 

time of printing.
The manufacturer assumes no liability for 

damage or injury resulting from failure to 

observe the operating instructions, use for 

other than the intended purpose, unprofes-

sional repairs, unauthorised modifications 

or use of non-approved spare parts and 

accessories, tools and lubricants.

Instructions on disposal

The packaging materials used can be 

recycled. When no longer required, 

dispose of the packing materials according 

to local environmental regulations.

This product may not be disposed of 

in the European Union via the normal 

household refuse. Dispose of the 

device via communal collection points.

The lubricant used can contain 

substances dangerous to the 

environment. Dispose of the lubricant 

according to local regulations. Observe the 

disposal instructions from the lubricant 

manufacturer.

General instructions

Summary of Contents for MAB 455























Reviews: