manualshive.com logo in svg

BDI JEFF BARE SOMA 6351, Instruction Manual

Share
Download
BDI JEFF BARE SOMA 6351 Instruction Manual Download Page 17

BDIUSA.COM  |  17

NEED  ASSISTANCE?  

[email protected]

CHANGING YOUR DISPLAY FROM INCHES TO CENTIMETERS

If you would prefer to see your display in metric dimensions, you can change this setting while your 
desk is in 

Reset Mode

. 

1.  Press the paddle DOWN until the desk is in its lowest position. Release the paddle.
2  Press and hold the paddle DOWN again until the display reads 

RESET

. Release paddle.

3. While the paddle says RESET, press the 

Menu Button

 to access the 

Settings Menu

.

4. Use the paddle to cycle through options,  pressing the 

Menu Button

 again to access the 

in   cm

 

settings.

5. Use the paddle to select IN (inches), CM (centimeters) or   to return you to the main menu.
6. Press the 

Menu Button

 again to program your selection.

7.  Press and hold the paddle DOWN once more until the desk lowers slightly, slightly rises, then 

stops. You have now exited Reset Mode.

ADJUSTING COLLISION SENSITIVITY ON YOUR DESKTOP

Your desktop includes a built-in collision sensor, stopping your desk automatically if anything 
comes in contact with it while in motion. By default, your desk is set to MEDIUM sensitivity. You can 
change this setting while your desk is in 

Reset Mode

. 

1.  Press the paddle DOWN until the desk is in its lowest position. Release the paddle.
2. Press and hold the paddle DOWN again until the display reads 

RESET

. Release paddle.

3. While the paddle says RESET, press and hold the 

Menu Button

 for five seconds to access the 

Settings Menu

.

4. Use the paddle to cycle through options,  pressing the 

Menu Button

 again to access the 

Collision 

Sensitivity

 settings.

5. Use the paddle to cycle through LOW, MEDIUM and HIGH to select the level of sensitivity desired. 
6. Press the 

Menu Button

 again to program your selection. This can take up to 15 seconds to 

reprogram.

7.  Press and hold the paddle DOWN once more until the desk lowers slightly, slightly rises, then 

stops. You have now exited Reset Mode.

For more information, detailed specifications, and online assistance, visit 

www.bdiusa.com/soma-lift

USING YOUR DIGITAL CONTROL PADDLE (CONTINUED)

Summary of Contents for JEFF BARE SOMA 6351





















Reviews:

No comments

Brands by name

Popular brands

Load more brands