Brook House,
Dunmurry Industrial Estate,
Dunmurry,
Belfast BT17 9HU
T +44 (0)28 9061 6505
F +44 (0)28 9061 6518
E [email protected]
elkay.co.uk
BROOK DESIGN HARDWARE LTD
B
D
H
B
D
H
BROOK DESIGN
HARDWARE LTD
B
D
H
BROOK DESIGN
HARDWARE LTD
BDH
BROOK DESIGN
HARDWARE LTD
B
D
H
Problem
Resolution
Lights will not
switch OFF
• Check time settings (Black bar denotes position of dip switches).
• Check Connections.
• PIR is too close to lights – Re-position away from lighting, forced air ventilation or heating sources.
• Ensure PIR is not looking directly at heat source or is in direct sunlight.
• PIR is re-triggered – Check area is left unoccupied for longer than time setting using an accurate time piece.
• Capacitor must be fi tted if switching low wattage loads, LEDs or fi tted at coil if switching contactors.
Lights will not
switch ON
• Check Terminal connections.
• Lux set too low – Turn up lux level towards the plus and wait 30 seconds for sensor to adjust.
• In the unlikely event that the above does not work then press the reset button at the back.
(In circuits with multiple PIRs ensure that all PIRs have reset buttons pressed).
Light switches
OFF then
immediately
comes back ON
• Check terminal connections.
• PIR may be detecting normally fi nd potential source that is triggering PIR. Best method is to cover
detector with thick material to eliminate potential trigger source.
• PIR is seeing infra-red heat from lighting load.
• Capacitor must be fi tted if switching low wattage loads, LEDs or fi tted at coil if switching contactors.
Diagram 1 – Time settings
Please note:
The black bar denotes the position of the dip switch.
10-15 sec 2 mins 3 mins 4 mins 5 mins 7 mins 10 mins 15 mins
TEST MODE
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
20 mins 25 mins 30 mins 35 mins 40 mins 45 mins 50 mins 60 mins
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
ON DIP
4
3
2
1
LIVE IN
LIVE OUT
NEUTRAL
SL L
SL L
N
LIVE IN
LIVE OUT
NEUTRAL
SL L
LIVE IN
LIVE OUT
NEUTRAL
SL L
N
N SL L
5 - 7m
4 - 6m
5 - 7m
3 - 4m
SL L
5 - 7m
4 - 6m
5 - 7m
3 - 4m
LIVE IN
LIVE OUT
NEUTRAL
SL L
SL L
N
N
LIVE IN
LIVE OUT
NEUTRAL
SL L
SL L
N
LIVE IN
LIVE OUT
NEUTRAL
SL L
LIVE IN
LIVE OUT
NEUTRAL
SL L
N
N SL L
5 - 7m
4 - 6m
5 - 7m
3 - 4m
SL L
5 - 7m
4 - 6m
5 - 7m
3 - 4m
LIVE IN
LIVE OUT
NEUTRAL
SL L
SL L
N
N
LIVE IN
LIVE OUT
NEUTRAL
SL L
SL L
N
LIVE IN
LIVE OUT
NEUTRAL
SL L
LIVE IN
LIVE OUT
NEUTRAL
SL L
N
N SL L
5 - 7m
4 - 6m
5 - 7m
3 - 4m
SL L
5 - 7m
4 - 6m
5 - 7m
3 - 4m
LIVE IN
LIVE OUT
NEUTRAL
SL L
SL L
N
N
Diagram 2 – Wiring
Troubleshooting
Diagram 3 – Detection 360
O
4-6m
3-4m
5-7m
Multiple switching
Single switching
Important Notice
All wiring should be carried out by a competent person
or a qualifi ed electrician and should be fi tted to current
IEE wiring regulations BS 7671. The circuit should be
isolated before carrying out any work. Failure to adhere
to the instructions will invalidate the warranty.
Technical Helpline
For further help, or information on this and the other products in the Elkay range
go to www.elkay.co.uk or call +44 (0)28 9061 6505. These instructions are
available in other languages. Please refer to our website www.elkay.co.uk
Instrukcje są również dostępne w innych językach. Prosimy o zapoznanie się z
naszą stroną internetową www.elkay.co.uk lub www.elkaypolska.pl
Elkay (Europe), 51C Milicka, Trzebnica, 55-100, Poland
