BCM EBC3410 User Manual Download Page 52

Page: 52 / 130

EBC-3410

BCM Advanced Research

3-51

3.6.32 Keyboard

and

PS/2

Mouse Connector (CN15)

Signal

MCLK

KCLK

VCC

4 3

GND

MDAT

2 1

KDAT

3.6.33 Signal Description – Keyboard & PS/2 Mouse Connectors (CN15)

KCLK

Bi-directional clock signal used to strobe data/commands from/to the PC-AT keyboard.

KDAT

Bi-directional serial data line used to transfer data from or commands to the PC-AT
keyboard.

MCLK

Bi-directional clock signal used to strobe data/commands from/to the PS/2 mouse.

MDAT

Bi-directional serial data line used to transfer data from or commands to the PS/2 mouse.

3.6.34 10/100BASE-Tx Ethernet Connector (CN16, CN17)

Signal

TXD+

TXD-

RXD+

RXD-

3.6.35 Signal Description – 10/100Base-Tx Ethernet Connector (CN16, CN17)

TXD+ / TXD-

Ethernet 10/100Base-Tx differential transmitter outputs.

RXD+ / RXD- Ethernet 10/100Base-Tx differential receiver inputs.

Summary of Contents for EBC3410



































































































































Search results

Summary of Contents for EBC3410

Reviews:

Brands by name

Popular brands

BCM EBC3410, User Manual

Search results

Summary of Contents for EBC3410

Reviews:

Brands by name

Popular brands