background image

 6 

 

 

SWITCH ANTI-HUM (GROUND ON / OFF)                  

.

 

Located under the amplifier 

 

Your  amplifier  EX-362D  has  a  mains  socket 
outlet with a  ground connection.  The  use  of 
this  type  of  connection  is  recommended  for 
electrical safety reasons (including wetlands). 

However sometimes this connection "mass" is the origin of 
"hum" audible from the speakers in a hi-fi  system to solve 
this  problem,  the  cancellation  of  the  ground  connection  is 
sometimes  sufficient.  To  do  this  you  have,  under  the       
amplifier, a switch to choose to connect or not the mass of 
the device to the mains. 
 

⑬ TRIGGER OUTPUT 

This  3.5  mm  Jack  mono  output  is  used  to  activate  or        
desactivate  remotely  auxiliary  devices  connected  to  the 
amplifier.  When  the  unit  is  turned  on,  the  output  is 
switched  to  12V.  When  the  unit  is  turned  off,  the  trigger 
output is 0V.  

⑭ AC MAIN INPUT 

Once all connections to the amplifier, plug the power cable 
into  an  outlet  and  turn  the  unit  on.  Your  amplifier  is  now 
ready for use.  

 

①  PHONE  /  HEADPHONES                                       

.

 

 
Important  note: 

Make  sure  the  volume  control  is  turned 

down  before  connecting  or  disconnecting  headphones.   
Listening  at  high  levels  can  cause  permanent  hearing      
damage. 

This  taken  Jack  size  6.35  mm  allows  connection  of  stereo 
headphones.  It  is  advisable  to  use  a  listener  with  an        
impedance  between  32  and  600  ohm  headphones.  When 
the  headset  is  connected,  the  output  to  the  speakers  are 
then cut.  

When the headphone jack is used, the speaker outputs are 
disabled.  Similarly,  the  bias  setting  of  the  power  stages  is 
reduced to a much lower than that used to power speakers 
level. This reduces the consumption based on actual needs 
of your listening.  

② STANDBY ON (SLEEP MODE) 

This button allows you to turn the device in Sleep mode to 
conserve energy while not performing his primary function 
or to resume the device in active mode. 

Regarding  the  high  level  of  heat  dissipation  of  the  device 
including  the  absence  of  any  musical  signal  (operating  in 
pure Class-A), we recommend that you turn the EX-362D in 
mode Standby when not in use.  

In  any  event,  for  security  reasons  the  EX-362D  is               
programmed  to  automatically  go  into  standby  after  12 
hours of operation (with or without the presence of musical 
signal).  If  the  EX-362D  gets  itself  into  Standby  when        
listening, you always have the option to return to operation 
with the Stand-By button. 

 

③ GAIN 

This command allows you to lower the overall gain (-10dB) 
on all of your sources. This allows you to adjust the fineness 
of  the  volume  adjustment  depending  on  the  sensitivity  of 
your speakers and your listening level. 

Connection to the amplifier 

Front panel 

Connections and uses 

Summary of Contents for EX362D













Reviews: