9
ENGLISH
FRANCAIS
SP
ANISH
DEUT
SCH
Specifications
Here you will find a number of fault description and possible
solutions we invite you to read in order to ensure the possibility
of an actual breakdown of your device.
The unit does not turn on
- Make sure the power cord is properly connected.
- Make sure the plug is fully inserted into the wall outlet and
there is power.
- Make sure the camera is turned on.
- Check the fuse in the mains plug or adapter if necessary.
There is no sound
- Make sure the unit is not in standby mode.
- Check that the source component is connected properly.
- Make sure you have selected the appropriate source
- Make sure your speakers are properly connected.
One channel no sound
- Make sure the balance control is in the correct position.
- Check the speaker connections.
- Check interconnects.
A loud humming or buzzing is noticeable
- Make sure that interconnect cable is loose or defective.
- Make sure your tape deck or turntable is not too close to the
amplifier.
- Check turntable or tonearm to capture an ground fault or a
faulty connection.
The bass is weak or the stereo image is diffuse
Make sure the speakers are not in phase.
The sound is distorted
Make sure that the control settings of volume or tone is not too
high.
The remote control does not work
- Check that the batteries have not expired.
- Make sure nothing is blocking the remote sensor.
WIRELESS - The sound stops or there is noise
If a device such as a microwave oven or wi-fi transmitter
generates electromagnetic waves near the 2.4 GHz band, it can
affect the connection or broadcast quality. In this case, install
the EX-332.2 at a greater distance from this unit.
WIRELESS - The transmission is interrupted
- The device connected to the EX-332.2 is perhaps too far. The
approximate distance transmission WIRELESS is about 10m
without obstacles.
- Make sure there are no obstacles between the EX-332.2 and
your WIRELESS device.
Digital-to-analog converter
The interface is entrusted to a Cirrus Logic CS8416 chip and the
digital-analog conversion is supported by a PCM1973 circuit
from Texas Instrument. The DAC is compatible with digital
signals up to 24bits/96kHz from coaxial and optical inputs.
Phono input
Input impedance: 47 KΩ
Frequency band (± 0.2dB of RIAA) : 10Hz - 60KHz
Gain: 45dB
Distorsion (1kHz, 1W, 8Ω) < 0.003%
Headphone output
2x300 mW into 300Ω
Switchs
- Mode (Mono / Stereo)
- AV ByPass (on Line 2)
- PH Bypass (on Line 3)
Connections
2x RCA line stereo input (LINE 1 and LINE 2)
2x XLR line stereo input (LINE 1 and LINE 2)
1x PHONO input switchable (or LINE 3)
2x Digitals inputs: 1x optical and 1x coaxial (DAT)
1x OPTIONAL CARD Input (to connect on OPTION RCA)
2x Subwoofer outputs mono (RCA)
1x Pré-out RCA and XLR stereo outputs
1x Trigger output (Jack 3,5mm mono)
1x Headphones output (stereo jack 6,35 mm)
1x BNC Phase tester
1x WIRELESS antenna
4x Speaker terminals screw-compatible banana plugs
1x IEC Detachable power cord
Included accessories
1x Detachable power cord
1x WIRELESS antenna
1x Remote control RC-EX2v2
2x Batteries (AAA) for remote control
1x Manual guide
General
PRODUCT
Dimensions (W×H×D): 430 x 135 x 400 mm
Weight: 18.7 kg
BOX
Dimensions (W×H×D): 500 x 205 x 465 mm
Weight: 25 kg
Volume: 0.48m
3
EAN CODES
EX-332.2-B (Black) : 0634654606143
EX-332.2-S (Silver) : 0634654606136
Specification and appearance are subject to change without notice. Weight and dimensions
are approximate. Illustrations in this manual might differ slightly from production models.
Troubleshooting
