5”, 6.5”, or 8” SUBWOOFER
PATENTED BASS TUBES
®
ENCLOSURE WITH BASS REFLEX/DUCTED PORT ALIGNMENT
HIGH EFFICIENCY OUTPUT
OPTIMIZED FOR SPACE EFFICIENCY
DESIGNED FOR CORNER LOADING
MOISTURE RESISTANT ENCLOSURE
BUILT IN 30 WATT MONO AMPLIFIER
@
2 OHMS
AMP IS 2 OHM STABLE
18dB ELECTRONIC CROSSOVER FIXED
@
120 Hz.
NOISE REJECTING BALANCED INPUT CIRCUITRY
BALANCED LOW LEVEL INPUT • BALANCED HIGH LEVEL INPUT
INPUTS ARE SUMMED MONO INTERNALLY
SELECTABLE AUTOMATIC TURN ON FEATURE
18dB PER OCTAVE SUBSONIC FILTER
@
15 Hz.
* The efficiency levels of all Bazooka subwoofer speaker systems are measured in the typical environment: In the low
bass region with one watt of power.
SYSTEM FEATURES
SPECIFICATIONS
3
EL5A
EL6A
EL8A
Woofer Size
5“
6.5“
8“
Voice Coil Size
1“ high power /high temp
1“ high power /high temp
1“ high power /high temp
Magnet Size
13 oz.
13 oz.
15 oz.
Frequency response
39-120 hz.
39-120 hz.
39-120 hz.
Efficiency
100 dB*
103 dB*
105 dB*
Dimensions
18.125“x5“x6“
18.125“x6.75“x8“
18.125“x8.5“x10“
Weight
11 lbs.
12 lbs.
14 lbs.
Impedance
2 ohms
2 ohms
2 ohms
BASS TUBES
®
enclosure - patented Bass Reflex/ducted port alignment
Notice that one end of the mounting plate is angled and the other is not.
Select the end that is best suited for your application and mount that end of
the plate to the dash panel. The switch can also be flush mounted into a
flat panel or factory switch knock out panel. Be sure that the place you
choose to flush mount the switch has enough clearance behind it before
you start the installation of the switch. Using the supplied mounting
panel as a template, etch the mounting hole on to the panel you wish
to mount the switch. Carefully cut out the mounting hole.
Option Two:
If the source does not have an Auto-Antenna lead (or if the Auto-Antenna
goes down during tape operation),you can connect the Amplified
Bazookas' Remote Turn On Wire to one terminal of the SAS On/Off
Switch and the Switch's other terminal to an accessory or ignition point
at the vehicle fuse block. In this configuration, the Amplified Bazooka
will be on whenever the ignition and the SAS On/Off Switch are both
on. This method may allow noise or turn-on-and-off transients to become
amplified when the source unit is not in use. If this occurs, simply turn
off the SAS On/Off switch when the source unit is not in use and this
noise will be eliminated. When you are using this Option, the Quick
Disconnect YELLOW On/Off Jumper Loop MUST be disconnected from
the wiring harness.
Option Three
:
The Amplified Bazooka has a built -in Auto Turn-On Feature. If you choose to
use this feature, the Amplified Bazooka will turn on automatically whenever
there is music present at the inputs (high level or low level input). Please
take notice of the Quick Disconnect Yellow On/Off Jumper Loop located
on the Amplified Bazooka wiring harness. SAS ships the Amplified
Bazooka with this Jumper Loop plugged into the wiring harness. When the
JUMPER LOOP plugged in, the Auto Turn-On Option is in the ON position
and the Amplified Bazooka will turn on automatically when it senses any
music at the inputs. The ORANGE wire should not be connected to anything if
this feature is being used. Be sure to insulate the end of the ORANGE wire
so that it will not short to ground, as this may damage the Amplified Bazooka.
TURN ON OPTIONS CONT.
12
