background image

TOYOTA 

 

2007 -  

BASS TUBE (BAZOOKA

®

Troubleshooting 
 
 
 Troubleshooting 
 
            Condition:                                                                         Check For: 

 

 

 

No sound from Bass Tube, however factory 

speakers still play 

 

 

 

 

Distorted Sound 

 

 

 

Low Sound  

 

 

 

 

Rattling Noises 

 

 

 

 

 

 

 

1.  Is the green L.E.D. lit on the Bass Tube?  
If not, check for 12 volts on pins of the Bass 
Tube Connector with the ignition on.  If 
either pin doesn’t indicate 12 volts, check T-
Harness connectors behind the radio. 

2.  Is the 14-pin Molex connector securely 
connected to the Bass Tube? 

3.  Is the ground ring securely fastened to the 
rear center Anchorage bolt? 

 

1.  Close the back hatch of the vehicle 

2.  Adjust the radio to a comfortable listening 
level, and then turn the “gain control” knob 
on the Bass Tube counter-clockwise until the 
sound becomes clean.   

 

1.  Close the back hatch of the vehicle 

2.  Adjust the radio to a comfortable listening 
level, and then turn the “gain control” knob 
on the Bass Tube clockwise until the sound 
becomes audible.  Do not adjust the level too 
high, as this will result in distorted sound.   

 

Rattling will be evident in some panels at 
extreme volume conditions, but make sure 
you have performed the following to 
minimize noise: 

1.  Securely tightened Mounting Hardware so 
Bass Tube Bracket does not move. 

 

 

 

 

 

Southeast Toyota Distributors, LLC

Page 7 of 9

Summary of Contents for BASE TUBE










Reviews: