Please read these instructions before using your work light. Be sure to charge the
work light before the fi rst use.
CAUTION: Do not use this work light in explosive atmospheres, near fl ammable
liquids, or where explosion-proof lamps are required. Do not immerse in water.
CAUTION: For light duty work only.
CHARGING
INITIAL USE
Fully charge the work light before the fi rst use. If the battery is new or has been
unused for several months, several charge and discharge cycles may be needed to
reach full battery capacity. To reach maximum performance, run the light to completely
discharge the battery and then recharge. Each charge cycle will extend the operation
time until maximum capacity is achieved. The charge time for maximum capacity is
approximately 8 hours.
REGULAR USE
Use only the supplied AC or DC charging adapter.
For best performance, charge the work light when the LED’s start to dim.
Connect the AC power adapter to the light. The red indicator will light.
The red light indicates the work light is being charged. The red light remains on until
the battery is fully charged. At full charge, the light turns off. The total time to full charge
varies depending on the remaining charge in the battery pack.
Keep the work light plugged into the charger to maintain a trickle charge.
TIPS TO EXTEND BATTERY LIFE
The work light’s Nickel Metal Hydride internal battery does not have any recharge
memory effect. Charging the work light often helps extend its useful life.
A new work light or one that has not been used for a long period of time may not
accept a full charge initially. This is normal and does not indicate a problem. Fully
discharge and then charge the unit several times to condition the battery pack for full
capacity. As the battery pack capacity increases the charge time shortens.
Charge the unit after each use, whether the work light is fully discharged or not.
Store the work light at room temperature
Instruction Manual
Model 2166
THANK YOU FOR PURCHASING THE 2166 RECHARGEABLE WORK LIGHT.
SAVE THESE INSTRUCTIONS.
OPERATION
TURNING THE WORK LIGHT ON/OFF
The work light has a 2 position rocker switch to activate either the fl oodlight or
spotlight.
FLOODLIGHT
Press the Rocker Switch to the Up position to activate the fl oodlight
SPOTLIGHT
Press the Rocker Switch to the Down position to activate the spotlight
TURNING THE WORK LIGHT OFF
The center position of the Rocker Switch turns the light off
INTEGRATED MAGNETS AND MAGNETIC HOOK
The work light has two integrated magnets, one in the body of the light and the
other at the tip. These magnets will support the weight of the light when magnetically
attached to a ferrous metal surface. The removable Magnetic Hook can also be
attached to either of the integrated magnets and offers additional hands-free options.
CLEANING
Disconnect the light from the power source
Wipe with a clean dry soft cloth
Do not use any solvent or abrasive cleaners
BAYCO PRODUCTS LIMITED 1-YEAR WARRANTY
WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in workmanship
and materials to the original purchaser for one (1) year from the date of purchase, and
includes the LEDs, housing, lenses, electronics, switches, rechargeable batteries and
chargers. Bulbs (other than LEDs) are covered for ninety (90) days from the date of
purchase. Disposable non-rechargeable batteries are excluded from this warranty.
Normal wear and failures which are caused by accidents, misuse, abuse, faulty
installation and lightning damage are also excluded.
Consequential damages, incidental damages or incidental expenses, including
damage to property are also not covered under this warranty. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specifi c legal rights,
which may vary from state to state.
IN NO EVENT WILL BAYCO PRODUCTS, INC. OR ITS AFFILIATES OR
SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND REGARDLESS OF THE FORM OF
ACTION, WHETHER IN CONTRACT, TORT (INCLUDING NEGLIGENCE), STRICT
LIABILITY OR OTHERWISE. THE TOTAL CUMULATIVE LIABILITY TO CUSTOMER,
FROM ALL CAUSES OF ACTION AND ALL THEORIES OF LIABILITY, WILL BE
LIMITED TO AND WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT
PAID BY CUSTOMER.
If this product is used for rental purposes, the warranty term is reduced to 90 days
from the date of purchase.
WARRANTY CLAIMS – USA
Return the product to the place of purchase for all warranty related issues. If this is
not possible, contact Bayco Customer Service for a Return Goods Authorization
(RGA). Do not return this product to Bayco without fi rst receiving an RGA Number
from Bayco Customer Service. When returning the product, the RGA Number must be
written on the outside of the shipping box.
WARRANTY CLAIMS – OUTSIDE OF USA
Return the product to the place where purchased for all warranty related issues.
EXTENT OF COVERED WARRANTY WORK
Bayco will repair or replace this product at our option. If it is determined that the
warranty is no longer in effect, Bayco will contact you with a repair estimate before
beginning any work.
WARRANTY QUESTIONS
If you have any questions about this warranty or any other Bayco product
inquiries, please contact Bayco Customer Service .
