Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.baycoproducts.com
INS-503-18
Operating Instructions for Models
503-563 and 904-964
13 Watt Fluorescent Light
Electrical Rating - All models use 125 Volts 60 HZ
CAUTION
Models 503-563
TO REDUCE THE RISK OF ELECTRIC SHOCK AND FIRE - PULL PLUG WHEN
SERVICING, OR WHEN RE-LAMPING - USE ONLY 13 WATT OR SMALLER BULB
Models 904-964
TO REDUCE THE RISK OF ELECTRIC SHOCK AND FIRE - PULL PLUG WHEN
SERVICING, CONNECTING/DISCONNECTING FROM THE LAMP OR WHEN RE-
LAMPING - USE ONLY 13 WATT OR SMALLER BULB
• DO NOT use in explosive atmospheres, near flammable liquids, or where explosion
proof lamps are required.
• DO NOT use in the proximity of vehicles or equipment when there is a risk of
flammable liquids coming into contact with the hand lamp
• DO NOT immerse in water
• DO NOT use in areas where water can accumulate or in rain or mist
•
CAUTION
: Risk of Electric Shock – For Light Duty Dry Location Use Only
IMPORTANT SAFETY INSTRUCTIONS
Models 503-563
This product has a polarized plug (one blade is wider than the other). As a safety feature,
this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord
unless the plug can be fully inserted. Do not attempt to defeat this safety feature.
Models 904-964
This product has a 3 prong polarized plug on the power cord. Do not attempt to bypass this
safety feature by removing the round plug and defeat his safety feature. This plug will fit into
a grounded outlet only one way. If the plug does not fit fully into the outlet, contact a qualified
electrician. Never use with a two wire extension cord.
WARNING: NOT FOR USE ABOVE HAZARDOUS LOCATIONS
CAUTION: DO NOT USE IN HAZARDOUS LOCATIONS AS REQUIRED BY THE
CANADIAN ELECTRICAL CODE, PART I
OPERATION
Plug into 120 Volt 60 Hz polarized outlet. Notice the polarized plug and insert
properly. Operate switch. Lamp may flash several times before lighting.
Some models have a 3-wire grounded outlet as a power source for electrical tools or
other
appliances not exceeding 6.4 AMPS. The outlet will also accept a two-wire polarized plug.
BULB REPLACEMENT
1. Disconnect the unit from electrical outlet
2. Remove the lens and & cover screws located on each side at the top end of lamp.
3. Pull the lens out and up to expose the bulbs
4. Slide the bulb holder cushion from around the top of the bulb. The bulb will remain
in the socket
5. Grasping the bulb at the top, pull forward and carefully pull up on the bulb to remove.
6. Insert the new bulb in the socket and bulb holder. Be sure the bulb is properly seated
against the bulb holder
7. Slide the bulb holder cushion back into place on the top of the bulb and align the
screw holes with the holes on the side of the light
8. Push the lens back into place on the front of the light and snap into place
9. Align the holes in the lens with the holes in the side of the light and replace the screws.
10. Restore power connection and test lamp by pressing the power switch.
NOTE: Even new lamps will flash several times before lighting.
REPLACEMENT BULBS
Use PL-13 twin-tube fluorescent bulb.
A replacement lamp may be obtained from Bayco products.
WARRANTY
1 YEAR WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in workmanship
and materials to the original purchaser for 1 year from the date of purchase, and includes
the LEDs, housing, lenses, electronics, switches, rechargeable batteries and chargers.
Bulbs (other than LEDs) are covered for 90 days from the date of purchase.
We will repair or replace this product should we determine it to be defective. This is the
only warranty, expressed or implied, including any warranty of merchantability or fitness for
a particular purpose.
For a complete copy of the warranty, go to www.baycoproducts.com/bayco-product-
support/warranties. Retain your receipt for proof of purchase.
Instructions Pour les Modèles
503-563 & 904-964 13 Watt Lampes
de Travail Fluorescente
Caractéristiques électriques - Tous les modèles utilisent 125 volts 60Hz
ATTENTION
Modèles 503-563
POUR REDUIRE LE RISQUE DE CHOC ÉLECTRIQUE ET INCENDIE - RETIRER LE
BOUCHON LORS DE L’ENTRETIEN OU QUAND REMPLACEMENT DES LAMPES -
UTILISER SEULEMENT 13 WATTS OU MOINS AMPOULE
Modèles 904-964
POUR REDUIRE LE RISQUE DE CHOC ÉLECTRIQUE ET INCENDIE - RETIRER LE
BOUCHON LORS DE L’ENTRETIEN, CONNEXION / DECONNEXION DE LA LAMPE
OU QUAND REMPLACEMENT DES LAMPES - UTILISER SEULEMENT 13 WATTS
OU MOINS AMPOULE
•
NE PAS utiliser dans des atmosphères explosives, près de liquides inflammables, ou
lorsque des lampes antidéflagrantes sont nécessaires.
• NE PAS utiliser à proximité de véhicules ou d’équipement quand il ya un risque de
liquides inflammables entrent en contact avec la lampe de poche
• Ne pas plonger dans l’eau
• NE PAS utiliser dans les zones où l’eau peut s’accumuler ou dans la pluie ou le brouillard
• ATTENTION: Risque de choc électrique - Pour la lumière endroit sec Duty Utilisez
uniquement
CONSIGNES DE SÉCURITÉ IMPORTANTES
Modèles 503-563
Ce produit a une fiche polarisée (une lame est plus large que l’autre). Par mesure
de sécurité, cette fiche ne rentre dans une prise polarisée que dans un sens. Si la fiche
n’entre pas complètement dans la prise, inverser la fiche. Si elle ne convient toujours
pas, contactez un électricien qualifié. Ne pas utiliser avec une rallonge si la fiche peut
être insérée à fond. Ne pas essayer de contourner ce dispositif de sécurité.
Modèles 904-964
Ce produit a une fiche à 3 broches polarisées sur le cordon d’alimentation. Ne pas
essayer de contourner ce dispositif de sécurité en retirant le bouchon rond et la défaite
de son dispositif de sécurité. Cette fiche dans une prise de terre une seule façon. Si la
