Bay Networks 58000 Installation And Reference Manual Download Page 16

Page: 16 / 158

Preface

xvi

893-878-B

Conventions

This section describes the conventions used in this guide.

Special Message Formats

This guide uses the following formats to highlight special messages:

Use of Enter, Type, and Press

This guide uses enter, type, and press to describe the following actions:

•

When you read “enter,” type the text and press the Enter key.

•

When you read “type,” type the text, but do not press the Enter key.

•

When you read “press,” press only the alphanumeric or named key.

Other Conventions

This guide uses the following additional conventions:

italics

Book titles and UNIX file, command, and directory names.

courier font

Screen text, user-typed command-line entries.

Initial Caps

Menu titles and window and button names.

[Enter]

Named keys in text are shown enclosed in square brackets.
The notation [Enter] is used for the Enter key and the
Return key.

[Ctrl]+C

Two or more keys that must be pressed simultaneously are
shown in text linked with a plus (+) sign.

Model 500x

Used when either the Model 5000 chassis or the Model

chassis

5005 chassis is applicable.

NOTE:

This format is used to highlight information of importance or special

interest.

CAUTION:

This format is used to highlight information that will help you

prevent equipment failure or loss of data.

WARNING:

This format is used to highlight material involving possibility of

injury or equipment damage.

893-878-B Book Page xvi Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands