Bay Networks 58000 Installation And Reference Manual Download Page 141 | Manualshive

Page: 141 / 158

background image

Using the System Configuration Menus

893-878-B

6-35

3.

Select either Soft Reset or Hard Reset.

The system prompts you to confirm your entry. The Model 58000 switch
immediately suspends the transmission of network traffic upon issuance of
this command. Network operation is resumed upon completion of the
reset.

4.

To reset the system to default, choose Reset to Default from the Reset
System menu and press Y to confirm your entry.

The Model 58000 switch immediately suspends the transmission of traffic
upon issuance of this command and resets the system to the default
parameters. Network operation is resumed upon completion of the reset.

Downloading an Image File

You can download a new image file without having to reset the switch by
selecting the appropriate option in the Reset System menu.

To download a new image file, follow these steps:

1.

Make sure the load parameters are set correctly, such as the TFTP
Load Server IP Address and Image File Name.

Refer to

Displaying and Modifying Boot Parameters

earlier in this chapter

for instructions on how to display and modify the image load parameter.

2.

Download Image from the Reset System menu.

The system prompts you to confirm your entry. The image file is
immediately downloaded.

893-878-B Book Page 35 Monday, May 12, 1997 2:06 PM

«
...
139
140
141
142
143
...
»

Summary of Contents for 58000































































































































































Reviews:

No comments

Related manuals for 58000

Brand: Lab.gruppen Pages: 35

Brand: Danfoss Pages: 61

Brand: Ubiquiti Pages: 22

UniFi UAP-AC-LR

Brand: Ubiquiti Pages: 28

Brand: XAVI Technologies Corp. Pages: 71

Brand: LaCie Pages: 22

Brand: Kramer Pages: 2

EdgeRouter PoE ERPoe-5

Brand: Ubiquiti Pages: 13

Brand: Global Sun Pages: 39

NVR2104/2108HS-W-4KS2 1U

Brand: Dahua Technology Pages: 363

Brand: TRENDnet Pages: 57

DotSurfer GPC-2100

Brand: Gtran Wireless Pages: 44

Brand: Abocom Pages: 59

LS-5100-16P-SI-OVS-H3

Brand: H3C Pages: 313

Brand: Zhone Pages: 494

Brand: Aegis Pages: 7

Brand: Huawei Pages: 3

Brand: Johnson Controls Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands