Bay Networks 58000 Installation And Reference Manual Download Page 137 | Manualshive

Page: 137 / 158

background image

Using the System Configuration Menus

893-878-B

6-31

Displaying and Modifying Boot Parameters

Initially, the Model 58000 switch boots using the information stored in its
nonvolatile RAM (NVRAM). The configuration information contained in the
local NVRAM specifies the location and name of the image file necessary to
boot the Model 58000 switch.

If you want to load a new software image file, you need to specify the image
file name and where the image file is stored. You can display and modify the
current boot parameters using the Boot Parameters menu.

The Boot Parameters menu provides a list of the current boot parameters and a
list of commands for modifying the boot parameters.

lists and

describes the boot parameters available in the Boot Parameters menu.

Table 6-7.

Boot parameters

Menu option

Description

Change effective

Modify Boot Mode

Specifies the source of the switch boot
parameters, either Local or Network (using
the BootP protocol) to be used at the next
system reset.

Immediately

Modify Image Load
Mode

Specifies the source of the switch image
file (either Local or Network) to be used at
the next system reset.

Immediately

Modify Boot Router
IP Address

Allows you to change the boot router IP
address.

After reset

Modify TFTP Load
Server IP Address

Modifies the IP address of the TFTP load
server.

Immediately

Modify TFTP Retry
Count

Changes the number of TFTP service
request retries before giving up.

Immediately

Modify Image File
Name

Modifies the Model 58000 switch image file
name to be downloaded.

Immediately

NOTE:

The Boot Parameters menu allows you to specify where the new image

is located (local or remote) and the name of the image file. However, you will
use the “Download Image” option from the Reset System menu to actually
download the image file.

893-878-B Book Page 31 Monday, May 12, 1997 2:06 PM

«
...
135
136
137
138
139
...
»

Summary of Contents for 58000































































































































































Reviews:

No comments

Related manuals for 58000

Brand: Parker Pages: 344

Brand: Panasonic Pages: 2

Brand: iDirect Pages: 52

Brand: NETGEAR Pages: 84

Brand: Speedtouch Pages: 124

Brand: Schrack Technik Pages: 2

Brand: WAGO Pages: 2

Brand: Abocom Pages: 63

AceroDURO 100/S100

Brand: CNC-Step Pages: 86

Brand: NetBurner Pages: 30

Brand: Thecus Pages: 130

Brand: ZyXEL Communications Pages: 28

Brand: Edimax Pages: 161

Brand: RadioLAN Pages: 24

Brand: Johnson Controls Pages: 28

Brand: Tripp Lite Pages: 2

Amplifi DHP-1565

Brand: D-Link Pages: 3

AirPro DWL-AB520

Brand: D-Link Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands