Bay Networks 58000 Installation And Reference Manual Download Page 134

Page: 134 / 158

Configuring the Model 58000 Switch

6-28

893-878-B

Select the new port duplex mode.

The system prompts you for confirmation. The modified ports use the new
duplex mode immediately.

Repeat steps 2 and 3 for additional ports.

Modifying Expansion Card Port Type

To modify the expansion card port type, follow these steps:

Choose Expansion Card Port Type from the Expansion Module Port
Configuration menu.

An Expansion Module Port Type menu similar to that shown in

Figure 6-15

is displayed.

Figure 6-15. Expansion Module Port Type menu

Bay Networks 58000 Ethernet Switch Module

System Up Time: 1 D-12H-22M-11S IP Address: 134.177.32.98(M)

MAC Address: 000081000201 Default Gateway: 134.177.32.1

Switch Software Version: 1.4.3 Subnet Mask: 255.255.255.0

Expansion Module Port Type

Port Operational Current Next Boot

MDA1 P1 [Act Feeder] [Auto] [Auto]

MDA1 P2 [Act Feeder] [Auto] [Auto]

MDA2 P1 [Act Feeder] [Auto] [Auto]

MDA3 P1 [Act Feeder] [Auto] [Auto]

MDA3 P2 [Act Feeder] [Auto] [Auto]

MDA4 P1 [Act Feeder] [Auto] [Auto]

MDA4 P2 [Act Feeder] [Auto] [Auto]

Change port type of MDA1 port1.

Use cursor keys to choose item. Press <RETURN> to confirm choice.

<CTRL><P>:Main Menu <CTRL><U>:Previous Menu <CTRL><L>:Refresh Screen

893-878-B Book Page 28 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands