manualshive.com logo in svg

Bay Networks 58000, Installation And Reference Manual

Share
Download
Bay Networks 58000 Installation And Reference Manual Download Page 133

Using the System Configuration Menus

893-878-B

6-27

 

Modifying Expansion Card Port Duplex Mode

To modify the expansion card port duplex mode, follow these steps:

1.

Choose Expansion Card Port Speed and Duplex Mode from the 
Expansion Module Port Configuration menu.

An Expansion Module Switch Port Speed and Duplex Mode menu similar 
to that shown in 

Figure 6-14

 is displayed.

Figure 6-14. Expansion Module-Switch Port Speed and Duplex Mode menu

2.

Choose the port you want to change.

The system displays the current duplex mode of that port and prompts you 
to enter a new speed and duplex mode. The current port mode is 
highlighted, and the port mode options are displayed unhighlighted.

Bay Networks 58000 Ethernet Switch Module

   System Up Time: 1 D-12H-22M-11S             IP Address: 134.177.32.98(M)

   MAC Address: 000081000201                   Default Gateway: 134.177.32.1

   Switch Software Version: 1.4.3              Subnet Mask: 255.255.255.0

Expansion Module-Switch Port Speed and Duplex Mode

                             Port Speed(Mb/s) Duplex Mode   

                     

        MDA1 P1    [100 Mb/s Half] 

                             MDA1 P2    [100 Mb/s Half] 

                             MDA2 P1    [100 Mb/s Half] 

                             MDA2 P2    [100 Mb/s Half] 

                             MDA3 P1    [100 Mb/s Half] 

                             MDA3 P2    [100 Mb/s Half] 

                             MDA4 P1    [100 Mb/s Half] 

                             MDA4 P2    [100 Mb/s Half] 

Change Port 1 speed and duplex mode.

Use cursor keys to choose item. Press <RETURN> to confirm choice.

<CTRL><P>: Main Menu  <CTRL><U>: Previous Menu  <CTRL><L>: Refresh Screen

893-878-B Book  Page 27  Monday, May 12, 1997  2:06 PM

Summary of Contents for 58000































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands