Bay Networks 58000 Installation And Reference Manual Download Page 118

Page: 118 / 158

Configuring the Model 58000 Switch

6-12

893-878-B

Configuring the Minimum System Parameters

Use the Configuration Parameters menu and appropriate submenus to configure
the following basic system parameters for the Model 58000 switch:

•

IP address

•

Default gateway address

•

Subnet mask

•

SNMP community strings

Displaying the Configuration Parameters Menu

To display the Configuration Parameters menu, choose Configuration
Parameters menu from the Main Menu. A Configuration Parameters menu
similar to that shown in

Figure 6-6

is displayed.

Figure 6-6.

Configuration Parameters menu

Bay Networks 58000 Ethernet Switch Module

System Up Time: 1 D-12H-22M-11S IP Address: 134.177.32.98(M)

MAC Address: 000081000201 Default Gateway: 134.177.32.1

Switch Software Version: 1.4.3 Subnet Mask: 255.255.255.0

Configuration Parameters

Switch Parameters

Boot Parameters

SNMP Parameters

Modify switch related parameters.

Use cursor keys to choose item. Press <RETURN> to confirm choice.

<CTRL><P>: Main Menu <CTRL><U>: Previous Menu <CTRL><L>: Refresh Screen

893-878-B Book Page 12 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands