Bay Networks 58000 Installation And Reference Manual Download Page 116 | Manualshive

Page: 116 / 158

background image

Configuring the Model 58000 Switch

6-10

893-878-B

The System Information screen only displays information: you must use the
Configuration Parameters menu to modify the Model 58000 switch parameters.

describes the fields on the System Information screen.

Table 6-3.

System information fields

Field

Description

Switch Firmware Version

Displays the current switch firmware version.

Switch Mode

Displays the switch mode for the Model 58000 switch.
Basic mode is the default mode. The Model 58000 switch
uses the virtual mode only if a VLAN is set up and ports are
assigned to that VLAN.

Memory
(Boot/Flash/NVRAM/DRA
M)

Displays the Model 58000 switch memory configuration.
Boot stores network boot code, power-up diagnostics, and
fault-isolation code.
Flash memory stores main agent and switch software
programs. NVRAM stores configuration data and some
statistics. DRAM is used by the CPU as an expansion of
main memory space.

Master Switch Priority

Displays the master switch priority configured for the local
hub. The priority range is from Hex number 0, the highest,
to FFFF, the lowest (default priority=8000). (If two or more
Model 58000 switches have the same switch priority, the
master switch is selected by the lowest MAC address.)

Master Switch
MAC Address

Specifies the MAC address of the master switch.
This parameter is read-only and determined at run-time.

Master Switch
IP Address

Specifies the IPaddress of the master switch.
This parameter is read-only and determined at run-time.

100 Mb/s
Full Duplex (Port #)

Lists the MDA ports that are operating at 100 Mb/s
full-duplex. MDA P1 means port 1 on the MDA.

100 Mb/s
Half Duplex (Port #)

Lists the MDA ports that are operating at 100 Mb/s
half-duplex. MDA P2 means port 2 on the MDA.

10 Mb/s
Full Duplex (Port #)

Lists 10 Mb/s ports that are operating at
full-duplex.

10 Mb/s
Half Duplex (Port #)

Lists 10 Mb/s ports that are operating at
half-duplex.

Trunk Ports

Lists ports that are directly connected to
another switch.

893-878-B Book Page 10 Monday, May 12, 1997 2:06 PM

«
...
114
115
116
117
118
...
»

Summary of Contents for 58000































































































































































Reviews:

No comments

Related manuals for 58000

Brand: Habitat Pages: 48

Brand: Winext Pages: 37

Brand: Justec Pages: 61

Net2Air Ins-40085-US

Brand: Paxton Pages: 4

Brand: ZyXEL Communications Pages: 215

IPAM-1600s Series

Brand: C-Com Pages: 148

Brand: ivideon Pages: 11

Brand: Icy Box Pages: 2

Brand: LevelOne Pages: 11

Brand: Goobay Pages: 20

Brand: TRENDnet Pages: 205

Brand: PACOM Pages: 16

3GStation Professional

Brand: Ubiquiti Pages: 24

Brand: UltrArmor Pages: 3

Brand: UfiSpace Pages: 34

Brand: ubiquoss Pages: 46

Brand: LOOQS Pages: 69

Brand: LOOQS Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands