manualshive.com logo in svg

Bay Networks 58000, Installation And Reference Manual

Share
Download
Bay Networks 58000 Installation And Reference Manual Download Page 110

Configuring the Model 58000 Switch

6-4

893-878-B

Menu Structure

All Model 58000 switch system configuration menus have a similar format. 
The screen layout is based upon common 80-character by 24-line ASCII 
terminal display characteristics. The menus are divided into three parts—the 
menu header, the command and status field, and the command line.

A sample system configuration menu is displayed in 

Figure 6-2

.

Figure 6-2.

Sample system configuration menu

Bay Networks 58000 Ethernet Switch Module

Main Menu

System Up Time: 1 D-12H-22M-11S

MAC Address:  000081000201

Switch Software Version: 1.4.3

IF Address: 123.123.11.11 (M)

Default Gateway: 123.123.11.1

Subnet Mask: 255.255.255.0

Use cursor keys to choose item. Press <RETURN> to confirm choice.

<CTRL><P>:Main Menu <CTRL><U>:Previous Menu <CTRL><L>:Refresh Screen

Display system information.

Configuration Parameters

Reset System

System Information

Main header

Command and status area

Command line

Displays help information

6496

893-878-B Book  Page 4  Monday, May 12, 1997  2:06 PM

Summary of Contents for 58000































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands