background image

110

MASTER (main) boiler parameter configuration

Parameter configuration on non-MASTERS boiler

Using the control panel, access menu 3, and carry out the following settings.

Menù

Programme 

line

Value

Description

Configuration

5977

None

Disabling of thermostat on terminal board M1 (1-2)

Configuration

6020

Multifunctional

Enabling unit AVS75

Configuration

6030

Heat circ. pump. 1Q2

Control of circuit 1 pump

Configuration

6040

Common delivery probe 

B10

Control of cascade delivery temperature

Configuration

6041

Cascade return probe B70 Control of cascade return temperature

Configuration

6046

Ambiance thermostat CR1

Enabling of thermostat in inlet H2 of the AVS75 

Configuration

6200

Yes (*)

Memorisation of modifications carried out

LPB

6630

Always

Identification of master boiler

LPB

6640

Autonomous

Setting of master cascade clock

*The value returns automatically to “No” immediately after setting.

Having configured he master boiler parameters as described in the previous paragraph, proceed to configuration of the other 
boilers. To this purpose, connect the Remote Control (if not already present) to the boiler to be configured and proceed as 
follows.

The operations listed below are repeated for each boiler in the cascade, excluding the MASTER boiler.

For correct system functioning an address must be assigned to each boiler so that it can be recognised by the master boiler (the 
master boiler has default =1). Moreover it is also necessary to synchronise the boiler clocks with that of the master boiler. Using 
the control panel, access menu 3 and carry out the following settings.

Menù

Programme 

line

Value

Description

Configuration

5710

OFF

Enabling of thermostat for circuit 2(terminal board M1 (1-2) in boiler)

LPB

6600

2..3..4..

Enabling unit AVS75

LPB

6640

Slave with imp. Remote

Setting cascade boiler clocks with master boiler

Menù

Programme 

line

Value

Description

Cascade

3540

N° of hours

Period of functioning before automatic change of sequence of main boiler.

Cascade

3541

First – Last – First and 

Last. 

Exclusion of the boiler(s) from periodic rotation of sequence

After connecting the pump to the relay, set outlet QX22 as shown in the following table.

Menù

Programme 

line

Value

Description

Cascade

6031

actuator HSW Q3

Control load pump of DHW storage on relay QX22

The pumps of the high temperature zone have to be connected one to each other, and through a relè, linked to the terminal of 
module AVS75 identified with QX21-N.

Summary of Contents for Luna Platinum 1.12






































Reviews: