background image

FLIGHT OPERATION 

Start the CORTEXpro in normal operation mode, without the jumper connected. The LED will flash for the first few seconds and indicates the 
system’s successful initialization. The model must not be moved during this process, otherwise, the stabilization will remain inactive (device 
flashes red constantly), until power-cycled again. 
When the system and gyros have been initialized, the servos will indicate this by a double bump on the surfaces. The LED lights up constantly; 
its colour indicating the setting (bank and mode) of the gyro channel. 
Each time switched on, the CORTEXpro recognizes the transmitter’s neutral trims. This is why no control movements must be given until 
initialization is completed.

LED

7

FOLLOW THE LED‘S SIGNALS (FLASHING)

AND/OR THE SERVOS (SURFACE BUMPS)

Keep the sticks neutral, wait for signal

...

Now move aileron to the right extreme, and hold

Now move aileron to the left extreme, and hold

Release aileron, 

Now „push“ elevator down fully, and hold...
Now „pull“ elevator up fully, and hold...

Release elevator, 

Now rudder right fully, and hold…
Now rudder left fully, and hold

Release rudder,

Now switch gyro channel by at least 25% signal difference…
Setup completed successfully. Now pull the jumper and switch off.

Do not move model or sticks durcing initialization.

Failure

: system not initialized due to movement! 

Waiting for input signal: LED pulses red

Failure

: no axis teached in!

Waiting for neutral sticks. If the LED blinks white continuously, repeast 

setup, or check the transmitter‘s neutrals.

After successful initialization, the servos will respond with a double 

bump.

Constant LED light => ready for operation

• 

If the jumper is pulled out before the end of the setup, the 

  system’s condition is undefined. Repeat setup.

• 

Do  not  teach  any  extremely  short  throws. This  can  lead  to 

 

  errors, as the system may not recognize any greatly reduced  

   throw as an input.  

NOTES REGARDING SETUP

• 

Setup sequence only starts in case of correct RC reception.

• 

Setup can be repeated at any time by power-cycling

  (with jumper in place). 

• 

If the device is switched off before the end of the setup 

  sequence, no changes will be saved, but a possible previous 

  setup retained.

Summary of Contents for CORTEXpro













Reviews: