Baumuller BUM 62 Operating Instructions Manual Download Page 47

Page: 47 / 74

Installation

Mono Power Unit BUM 62, 63, 64

Baumüller Nürnberg GmbH

5.94005.12

Sub-unit terminal X99AB

WARNING

The allowed maximum current of 10 A per terminal connection must not be exceeded, otherwise there
is a risk of damaging the devices. With higher current requirements, there must be several, separate
current feeds.

Terminal-No.

Assignment

1, 2

BB ext (PELV)

Relay output: Ready for use of supply converter

24 V, 0.5 A max.

3, 4

Alert (PELV)

Relay output: Alert of supply converter

24 V, 0.5 A max.

+ Reset with 24-V signal (PELV)

Input for resetting error messages of the supply converter

(potential-free optocoupler input, 10 ... 25 mA)

Ground reset (PELV)

Reference point for resetting error messages of the

supply converter (potential-free optocoupler input)

Summary of Contents for BUM 62











































































Search results

Summary of Contents for BUM 62

Reviews:

Related manuals for BUM 62

Brands by name

Popular brands

Baumuller BUM 62, Operating Instructions Manual

Search results

Summary of Contents for BUM 62

Reviews:

Related manuals for BUM 62

Brands by name

Popular brands