manualshive.com logo in svg

Baumuller BM5-O-SAF-002, Operation Manual, Page: 95 / 182

Share
Download
Baumuller BM5-O-SAF-002 Operation Manual Download Page 95

NOTE!

The inputs comply with the specification type 3 according to EN 61131-2.

Interfaces

Operation Manual 

Safety Module for b maXX 5000

 BM5-O-SAF-002/3

Document no.: 5.11016.03 

95

of 180

11

Technical Data see 

Z

C.2 Technical Data safe inputs, STO-Inputs and Daisy-Chain-

Inputs

– 

from page 163 onward.

11.3.3 Daisy-Chain Cascading

The Safety Module has 2 Daisy-chain cables on two channels. 

The Daisy-chain-inputs and -outputs on two channels enable the module-independent 
linking of safety functions. This is, e.g. necessary, if several or all drive axes of an 
application must have the status STO (Safe Torque Off) or if a safe reduced speed is 
necessary for all axes.

The fast STO-reaction saves time in contrast to a field bus solution. 

Daisy-chain-inputs and -outputs can be parameterized with parameter tools. For 
example, the safety function, which shall be enabled on the corresponding Safety 
Module, in order to activate the Daisy-chain-input, can be set.

An open chain as well as a closed ring structure existing of several drive axes, can be 
made with the Daisy-chain-inputs and -outputs. The Daisy-chain consists of two control 
cables, which are wired as shown in 

Z

Figure 47

– 

on page 95.

Daisy-Chain Example - Open Chain 

An open chain is shown in the following figure. The safe inputs of the module axis 1 are 
configured in such a way, that they enable . the safety functions STO (Safe Torque Off) 
and SS1 (Safe Stop 19). Both safety functions are transmitted to the module axis 2, if an 
accordant parameterization of Daisy-chain-output of module axis 1 was made. The 
Daisy-chain-input of module axis 2 is configured, so that the function SS1 is operating. 
The configuration of the Daisy-chain-output of module axis 2 makes sure that the safety 
function SS1 is transmitted to axis 3. The Daisy-chain input of module axis 3 activates the 
function SS2 (Safe Stop 2). 

Figure 47:

Daisy-chain cascading - Example of an open chain

11.3.3.1 Daisy-Chain-Inputs

The Safety Module has two safe Daisy-chain-inputs on two channels.

Each Daisy-chain-input on two channels can be assigned to a safety function or the 
Daisy-chain-input of the Safety Modules can be activated/deactivated with the 

Summary of Contents for BM5-O-SAF-002























































































































































































Reviews:

No comments