Baumuller BM5-O-SAF-002 Operation Manual Download Page 138

Page: 138 / 182

Detecting errors in the periphery

Operation Manual

Safety Module for b maXX 5000

BM5-O-SAF-002/3

Document no.: 5.11016.03

Baumüller Nürnberg GmbH

138

of 180

19.4

The lists of the diagnosis- and error statuses are listed in

Operating states and error

messages

–

from page 138.

WARNING!

Do not put a defective safety-oriented system back into operation as long as the
cause of the error is unknown or an error has not been detected.

19.4 Detecting errors in the periphery

The safe input and output have diagnostic functions in order to detect short circuits and
crossfault on the input and output cables (see

External Interfaces

–

on page 93).

Electronic sensors must have an own error detection regarding short circuits on the
output.

CAUTION!

An elimination of errors for short-circuits on line must be made for safe outputs, which
are used separately in order to safely switch-off an actuator. Measures must be taken
in accordance with EN ISO 13849-2.

19.5 Operating states and error messages

Description of operating states in parameter

201.12

and the possible status- and

error states in

201.13

201.12

Description

201.13

Description

Initialization

Request synchronization telegram

Acknowledgment of synchronization telegram

Request of Session ID for FSoE

Acknowledgment of Session ID for FSoE

Switch on LEDs

Switch on waiting time

Switch off waiting time

Waiting for test manager and online test

Waiting for initialization of the GDP protocol

Summary of Contents for BM5-O-SAF-002























































































































































































Search results

Summary of Contents for BM5-O-SAF-002

Reviews:

Baumuller BM5-O-SAF-002, Operation Manual, Page: 138 / 182

Search results

Summary of Contents for BM5-O-SAF-002

Reviews: