Baumuller b maXX 1000 Parameter Manual Download Page 132

Page: 132 / 210

Parameter description

Parameter manual

b maXX

1000

Document no. 5.07004.03

Baumüller Nürnberg GmbH

132

of 208

4.3

P1364

This parameter defines an upper bound or limit for the integral gain (I) and therefore limits
the master frequency.

The formula is:

Integral upper bound = maximum output frequency

This parameter can limit the maximum output frequency.

Complete PID diagram see

P1369

–

P1365

To avoid amplification of measurement noise in the controller output, a derivative digital
filter is inserted. This filter helps to dampen oscillations.

Complete PID diagram see

P1369

–

P1366

This parameter defines the percentage of output frequency limit during the PID control.
The formula is:

Output frequency limit = maximum output frequency

This parameter will limit the maximum output frequency. An overall limit for the output fre-
quency can be set in

P0040

–

Complete PID diagram see

P1369

–

P1364

Obere Grenze Integralverstärkung

0 to 100 %

Upper bound for integral control

100 %

STOP

BM_u_UpperBoundIntegralControl

1:1

P1365

Hauptfilter Verzögerungszeit

0.0 to 2.5 s

Primary delay filter time

0.0 s

STOP

BM_u_PrimaryDelayFilterTime

10:1

P1366

Ausgangsfrequenz Grenze

0 to 110 %

Output frequency limit

100 %

STOP

BM_u_OutputFrequencyLimit

1:1

Summary of Contents for b maXX 1000



















































































































































































































Search results

Summary of Contents for b maXX 1000

Reviews:

Brands by name

Popular brands

Baumuller b maXX 1000, Parameter Manual

Search results

Summary of Contents for b maXX 1000

Reviews:

Brands by name

Popular brands