17
18
Identify usual trouble of washer
No
washing
Abnormal
draining
Abnormal
spin
List of faults and inspection
Faults
Inspection Items
No water
flows in
If the power is off or the fuse is burned out.
If the water supply is cut off or the water pressure is too low.
If the inlet hose is properly connected and the water tap is opened.
If the filtering screen of inlet valve is blocked by dirt.
If the coil of inlet valve is damaged. (The slight electromagnetic
sound is normal phenomenon when the inlet valve is switched on)
If the "Start / Pause" button is pressed after the power
switch is pressed.
If the door lid is closed.
If all clothing piled largely at one side of barrel or the clothing
is excessively placed.
If the washer is not placed in stable condition or it is placed in
inclination state. (The ground is not flat).
If the motor belt is loosened.
Note: During the de spin process, if washing are piled at one side of the spin barrel,
it will cause unbalance of spin barrel resulting in striking. At this moment, the
computer inside the washer will feel this unbalance phenomenon and will automatically
correct it ( fill in water Washing ). However, if unbalance situation is not removed after
continuous three corrections, which means the computer auto-correction can not
resolve the problem. Then the user has to manually and evenly place the clothing
inside the barrel to solve the problem.
When the washer is in trouble, please contact local service office or the sales service
department of our company and the customer should not dismantle the machine without
permission.
If the washer can not work normally, or appear abnormity or alarms, please check and
correct as follows.
If the water drain hose is placed very high.
If the end of water drain hose is sealed in pond.
If the internal rubber ring of drain valve is blocked by dirt.
If the power is off or the fuse is burned out.
If the power supply voltage is too low.
If the water amount reaches to the required water level.
(The washer will not work if the water amount does not reach the
required water level)
If it is set to "Delay" washing mode. (It will only start to work
until the reservation time reached)
Cleaning and Maintenance of the washing machine
End of program
The washing machine will send off the
sound of “dou-dou” at the end of any
program operation to remind you to take
out the laundry or operate it again.
After the sound, the washing machine
returns to its power-off state with no
display and all lights off.
Please shut off the tap, pull out the plug
when not in use to avoid water leakage or
the fire accidents.
Maintenance
Use gentle clothing to wipe off the water and
dirt on the surface each time after using the
washing machine. Detergent, propellant and
other chemicals are not allowed
to use so as to avoid any
damage to the plastic
accessories.
Clean the water inlet
Clean Of the filter
After long time use, the
water
inlet mesh
bag may be blocked with smudginess, and
should be cleaned according to the
following steps:
1.Switch on the power, followed by shutting
off the tap.
2.Let the washer works for 5 seconds so
that water flows into the tub through the
water inlet hose.
then turn off the power.
3.Unload the water inlet hose and clean
the mesh bag, then restore the water inlet
assembly.
After using the washing machine for a
period, please clean it according to the
following steps:
1.Take off the
lint
filter.
2.Turn over the mesh bag and wash it
clean in the water.
3.Restore it and fix it.
Note:
If the drain filter is not cleaned at proper time (every 10 times of use),
Drain problem could
be caused.
1. Drain the water out of the
pump, under which use a
container to collect.
2. Loosen the pump
cover anticlockwise.
3. Take out the lint filter.
4. Clean the filter.
5. Restore it and adjust
the convex place to align
at the pump hole.
6. Tighten the pump cover
clockwise.
Clean the lint filter in the drain pump (only for having drain filter)
(only for normal filter)
After
using
the
washing
machine
for
a
period
,
please
clean
it
according
to
the
following
steps
:
1
.
Take
out
the
lint
filter
.
2
.
Open the filter
and
wash
it
clean
in
the water
.
3
.
Restore
it
and
fix
it
.
(only for magic filter)