background image

 

 

Use only original components or replacement components received from Bauman 
Manufacturing. 

 

Sitting, reaching into or climbing on or in the spreader during operation can result in 
serious injury or death.  Do not ride on the spreader while the vehicle is in motion. 

 

All laws and rules relating to public safety in the country of operation must be obeyed.  
Follow both the vehicle and spreader manuals to ensure safety and mechanical 
efficiency. 

 

     

It is the operator’s responsibility t

o ensure the safety of themselves and others 

while operating or maintaining a Bauman Drop Spreader. 

 
 
 
 
 

SAFETY LABELS 

 

The danger labels on Bauman Manufacturing equipment are for the safety of the operator as 
well as pedestrians and bystanders.  Read and obey warning and danger labels.  The operator 
must ensure that before operating the machine, all guards and grills are in place and that they 
are attached properly.  Stay clear of all moving parts and rotating shafts. 
 

           Under no circumstances should anyone reach into the 

        hopper when the spreader is in operation. 

 

 

 

 

Summary of Contents for 1040SI





















Reviews: