5019 401 15155
Add the detergent as described in the chapter
“Detergent and Additives” in the booklet.
1. Turn the
programme selector knob
in
any direction to the desired programme.
The remaining time display shows the
duration of the chosen programme (in
hours and minutes) and the pilot lamp
above the
“Start/Pause”
button is
flashing.
2. The programme sequence indicator and
the indicator with the maximum possible
spin speed light up.
3. The temperature can be altered by pressing
the
“+”
or
“-”
button under the
corresponding LED display.
“Prewash” button
• Only for heavily soiled laundry (for example
sand or granular dirt). Programme duration is
increased by some 15 min.
“Intensive Rinse” button
• An additional rinse cycle is carried out.
• This additional option is particularly
suitable for areas with very soft water, for
washing baby linen and helping people
with detergent allergies.
“Rinse Hold” button
• The laundry remains in the last rinse
water without being spun: discoloration
of the laundry and additional creasing are
prevented.
• This additional option is particularly
recommended for the programme
“Synthetics” or “Delicates”.
• This additional function is particularly
useful if you want to postpone spinning
to a later time.
Note:
the programme has reached the
“Rinse Hold” when the “Rinse Hold” button
light flashes.
Terminate the “Rinse Hold” option:
• Press the “Rinse Hold” button again; the
programme will terminate automatically
with the appropriate spin cycle for the
current programme.
• If you do not wish to spin the clothes, turn
the programme selector knob to “Drain/
Cancel” and press the “
Start/Pause
”
button again.
“Speed Reduction” button
• A maximum spin speed is assigned to each
programme.
• Press the button to set another speed for the
spin cycle.
• If the spin speed “0” is selected, the final
spin is cancelled. The water is drained out
only.
CONSUMPTION DATA
*
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Programme duration **
approx.
(hours : minutes)
White Cotton
95
5.0
44***
1.90
1:55
Coloured cotton
60
5.0
39
0.95
2:00
Coloured cotton
40
5.0
39
0.60
2:00
Synthetic
60
2.5
55***
0.70
1:30
Synthetic
40
2.5
50
0.50
1:15
Rapid wash
30
3.0
35
0.40
0:30
Delicate
30
1.5
50
0.50
0:45
Wool
40
1.0
50
0.60
0:40
Handwash
30
1.0
35
0.40
0:35
*
Consumption
values
were measured in normalized conditions in compliance with Standard IEC 60456.
** The
programme duration
may also vary from the chart values. The washing machine is able to allow for
particular household conditions and to adapt the programme run time accordingly.
*** To reduce
the water temperature
, some cold water is
added at the end of the main wash cycle, before
the pump drains the water out.
POUR IN DETERGENT, CLOSE THE
DOOR AND SELECT A PROGRAMME
SELECT SPECIAL OPTIONS - The
indicator lights go on.
“Easy Ironing” button
• To lessen creasing, the water quantity is
increased and the clothes are spun very
gently at reduced power. This makes your
laundry significantly damper at the end of
the programme.
The “Start Delay” allows to run the machine
at the consumer's convenience, for example
at night when electricity is cheaper.
• Press the “Start Delay” button. Select the
programme start from 1 to 19 hours
ahead by pressing the button again.
• Press the
“Start/Pause”
button. The
Start Delay indicator light flashes until the
programme starts.
• During programme start the remaining
time appears in the digital display.
“Start Delay” correction.
• Before the “Start Delay” has been started:
The preset number of hours can be
altered by continuously pressing the
“Start Delay” button.
The number of hours can be reduced by
first turning the programme selector
switch to the “Off” position. Then set the
programme again and select the desired
number of hours.
• After the “Start Delay” has been started:
The preset number of hours can be reduced
by pressing the “Start Delay” button again.
To increase the number of hours
preselected, first turn the programme
selector switch to the “Off” position. Then
set the programme and the additional
options again and select the desired
number of hours.
After you have selected the programme and
the additional option, the indicator light over
the
“Start/Pause”
button flashes. Turn on
the tap and start the programme by pressing
the
“Start/Pause”
button. Now the indicator
light above the button goes on.
In addition, all programme phases are
indicated by the associated lights. After the
end of a programme phase the associated
indicator light goes out. Thus the
programme sequence indicator moves from
left to right across the wash, rinse and spin
phases. At the end of the programme only
the “End” indicator is still on.
In the first 15 minutes after the start of the
“Cotton”, “Coloured Cotton” and “Synthetic”
programmes the door can be opened to add
further laundry. This is not possible if “Rapid
Wash” is selected.
• The remaining time display shows “0:00”
and the “End” display lights up.
1. Turn the programme selector knob to the
“Off” position.
2. Turn off the tap.
3. Open the door and unload the machine.
A newly-selected programme will continue
in the same programme section during
which the current programme was
interrupted. Therefore do not add any more
detergent.
1. Press the
“Start/Pause”
button to
interrupt the programme. The indicator
light flashes.
2. Select the new programme (with
temperature), any additional options and
- if you wish - another spin speed.
3. Press the
“Start/Pause”
button again to
restart the programme.
• If you are in the “Prewash” programme step
this additional option can not be deselected
as described (to do this see “Interrupt/Cancel
Programme).
1. Press the
“Start/Pause”
button to
interrupt the programme. The indicator
light flashes.
2. Set the programme selector to “Drain/
Cancel”. The spin speed
“0”
and the
remaining time “2 minutes” are displayed.
3. Press the
“Start/Pause”
button to start the
“Drain/Cancel” programme.
START DELAY
PROGRAMME START
DOOR LOCK
PROGRAMME END
RESELECT AFTER PROGRAMME START
CANCEL/DELETE PROGRAMME
