Bauknecht WA3108, Instructions For Use Manual

Page: 16 / 21

16
Fault display table
a. Fault in the water supply
The appliance has no or
insufficient water supply.
For models with a fault display,
the
“Tap Off” display lights up
and the spin speed indication
LED flashes. If a digital display is
fitted, “H” and “F” are also
displayed alternately.
For models with no fault display,
the washing machine stops in the
appropriate programme step.
Switch the appliance off and pull
out the mains plug.
Check whether:
• the water tap is fully turned
on, and the water supply
pressure is sufficient
• the water inlet hose is kinked
• the water connection mesh
filters are blocked (see “Care
And Maintenance”/”Mesh
Filters in the Water
Connection”)
• the water supply hose is
frozen up
• the washing machine has a
safety hose and the safety
valve is open (red indicator in
the safety valve inspection
window); In this case replace it
with a new safety hose
Reconnect the appliance to the
electrical socket.
For models with a fault display,
reselect the desired programme
and start it.
For models without a fault
display continue the programme
by pressing the “On/Off” button
again.
If the fault occurs again, please
contact After-Sales Service (see
“After-Sales Service”).
b. Draining fault
Waste water not pumped out.
For models with a fault display,
the spin speed indication LEDs
flash. If a digital display is fitted,
“P” and “F” are also displayed
alternately.
For models with no fault display,
the washing machine stops in the
appropriate programme step.
Switch the appliance off and pull
out the mains plug.
Check whether:
• the drain hose is kinked
• the pump or the filter is
blocked (see “Removing The
Filter”)
IMPORTANT: before
draining, make sure that the
water has cooled down.
• The water in the drain hose is
frozen up
Reconnect the appliance to the
electrical socket.
For models with fault display,
select and start the “Drain/
Cancel” programme.
To rinse the laundry, we then
recommend a short programme
without the addition of
detergent.
For models without a fault
display continue the programme
by pressing the
“On/Off” button again.
If the fault occurs again, please
contact After-Sales Service (see
“After-Sales Service”).
c. Fault in an electrical
component
The appliance stops in the middle
of a programme.
For models with a fault display,
the spin speed indicator LEDs
flash. If a digital display is fitted,
“F4” to “F16” are also displayed.
Switch the washing machine off.
First of all select and start the
“Drain/Cancel” programme.
Then select and start the desired
programme again.
For models with no fault display,
the washing machine stops in the
appropriate programme step.
First switch the washing machine
off and on again to continue
with the programme.
If the fault persists, please
contact After-Sales Service (see
“After-Sales Service”).
d.
“Water Stop” fault (if
fitted)
The “Water Stop” fault may have
been triggered by:
1.
excess foaming
2. a leak in the washing machine.
In this case the pump is switched
on automatically in order to
pump the water out.
For models with a fault display,
the “Water Stop” indicator lights
up and the spin speed indicator
LEDs flash. If a digital display is
fitted, “A” and “F” are also
displayed alternately.
For models with no fault display,
the washing machine stops in the
appropriate programme step.
Switch the appliance off, pull out
the mains plug and turn the
water tap off.
Tilt the appliance forwards
carefully to allow the collected
water to flow out from the
bottom of the appliance.
Luminous display
Spin
speed
lights
Digital display
(if fitted)
Fault description
“Water tap” flash “H” and “F” “Fault in water supply”
- flash “P” and “F” “Draining fault”
- flash from “F4” to “F16” “Fault in an electrical component”
“Water Stop” flash “A” and “F” “Water Stop fault”