5019 407 00124
1. Check that all fastenings are closed and
that pockets are empty.
2. Turn the articles inside out.
3. Place laundry loosely in the drum to
make sure it doesn’t become tangled.
Sort laundry as follows:
A) By care symbols (on the collar or
inside seam):
Suitable for tumble drying
Tumble drying with reduced
drying intensity only. Press
gentle button
Do not tumble dry
B) By amount and thickness/weight
Whenever the load to be dried exceeds
dryer capacity, separate laundry
according to weight (e.g. towels from
thin underwear).
C) By type of fabrics
Cotton/linen
: towels, cotton jersey,
bed and table linen made of cotton or
linen.
Synthetics/Easy Care
: blouses, shirts,
overalls, etc. made of polyester or
polyamide, as well as cotton/synthetic
mixes.
D) By drying level
• Sort into: iron dry, cupboard dry, etc.
Do not tumble dry:
woollens, silk, nylon
stockings, delicate embroidery, fabrics
with metallic decorations, bulky items such
as sleeping bags, etc.
Important: only use specific indicated
dryer-safe additives
and rinse items
that have been treated with stain remover
thoroughly in plenty of water before
drying.
Only use specific indicated
dryer-safe plastic items
and never dry
rubber or articles contaminated with
vegetable oil in the dryer
Programme and Options:
•
To select a programme, turn the
programme selector knob to the
required position. The Start/Pause
indicator lamp is blinking, indicating
that the cycle needs to be started.
•
To select an option, press the
corresponding button. The indicator
light above the button lights up
confirming that the selection has been
made.
•
Press the option button again to cancel
the option.
1. Having selected the desired
programme and options, press the
Start/Pause button.
If the laundry is not removed at the
end of the drying cycle, an automatic
anti-crease cycle will operate for
maximum 60 min. The drum rotates at
regular intervals, preventing the
laundry from creasing.
Anti-Crease protection re-
distributes laundry in the drum.
When the Anti-Crease option is
selected and laundry has not been
taken out, an anti-crease cycle is
activated for 12 hrs.
2. On completion of the programme, set
the programme selector knob to
position
“0”
.
When changing the programme during
the drying cycle, the dryer stops. The Start/
Pause indicator lamp is blinking.
To operate the new programme, press the
Start/Pause button.
To interrupt the dryer during operation
1. Set the programme selector knob to
Airing.
2. Press the Start/Pause button.
Wait at least 5 minutes before opening
the door to allow the dryer to cool
down.
For your safety the programme stops
automatically if you open the door.
3. To restart, after door opening, close
the door and press the Start/Pause
button again.
Clean the lint filter at the end of every
drying cycle:
1. Open the door.
2. Pull the filter upwards.
3. Open the filter.
4. Remove lint using a soft brush or your
fingertips.
5. Close the filter.
6. Push the filter back into place
.
Empty the water container at the end
of every drying cycle.
1. Pull the handle to remove the water
container.
2. Empty the water container.
3. Replace the water container when
empty by pushing it
completely
back
in place.
If a fault occurs, before contacting our
After-Sales Service, make the
following checks to try and remedy
the problem:
Drying takes too long / laundry is not
dry enough:
•
Was the correct programme selected?
•
Was the inserted laundry too wet
(Washing machine spin speed less than
800 rpm? When the spinning speed is
less than 800 rpm the water container
fault may occur during the drying cycle)?
•
Is the lint filter dirty (filter indicator
lamp on)?
•
Is the heat exchanger dirty (refer to the
Instructions for use)?
•
Is the ambient temperature too high?
The dryer does not operate:
(after a power failure and/or
interruption to the mains supply,
always press the Start/Pause button).
•
Is the plug properly inserted into the
mains electricity socket?
•
Is there a power failure?
•
Has the fuse blown?
•
Is the door properly closed?
•
Has the programme been selected?
•
Has the start-delay option been
selected?
•
Has the
Start/Pause
button been
pressed?
Lint filter or water container indicator
lamp on:
•
Is the lint filter clean?
•
Is the water container empty?
•
Is the water container correctly
positioned?
•
Is the heat exchanger clean?
Water droplets underneath the dryer:
•
Is the heat exchanger correctly
positioned?
•
Has any fluff on the heat exchanger
seal been wiped away?
•
Has any fluff on the door seal been
wiped away?
•
Has the water container been
positioned correctly?
All programme sequence indicators
blinking:
•
Service call necessary.
Replacing the drum light bulb (if
supplied):
•
If the inside lamp does not work, the
bulb may be faulty.
•
Unplug the dryer.
•
Open the door and unscrew the glass
cover insie the drum.
•
Replace the faulty bulb with a new one
and screw the glass cover back on.
•
Replacement bulb: Philips 15W,
230/240V, E14.
If, after carrying out the above checks the
malfunction persists or appears again, turn
the dryer off and call our After-Sales
Service (refer to guarantee).
Please specify:
•
The nature of the fault.
•
The dryer type and model.
•
The service code (the number after the
word Service on the adhesive rating
plate) on the right-hand side when the
door is open.
•
Your full address and phone number.
PREPARING THE LAUNDRY
SELECTING A PROGRAMME & OPTIONS
STARTING & COMPLETING A
PROGRAMME
CHANGING A PROGRAMME
INTERRUPTING A PROGRAMME
DAILY MAINTENANCE & CLEANING
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
