background image

EN-12

8. FORWARD AND REVERSE ROTATION CONTROL (SEE FIG. F)

To change the rotational direction, push the forward/reverse selector switch to the right position (as 

viewed from the front of the drill). The rotation will now be forward rotation. Push the forward/reverse 

selector switch to the left position. The rotation will be backward rotation.

Warning: Never change the direction of rotation when the tool is rotating, wait until it has stopped.

WORKING HINTS FOR YOUR IMPACT DRILL

1. Drilling masonry and concrete

Select the drill/impact action selector switch to the “hammer symbol” position. Tungsten carbide drill bits 

should always be used for drilling masonry, concrete etc with a high speed.

2. Drilling steel

Select the drill/impact action selector switch to the “drill symbol” position. HSS drill bits should always be 

used for drilling steel with a lower speed.

3. Pilot holes

When drilling a large hole in tough material (i.e. steel), we recommend drilling a small pilot hole first 

before using a large drill bit.

4. Drilling tiles

Select the drill/impact action selector switch to the “drill symbol” position to drill the tile. When tile has 

been penetrated, switch over to “hammer symbol” position.

5. Cool the motor

If your power tool becomes too hot, set the speed to maximum and run no load for 2-3 minutes to cool 

the motor.

MAINTENANCE

Remove the plug from the socket before carrying out any adjustment, servicing or 

maintenance.

Your power tool requires no additional lubrication or maintenance. There are no user serviceable parts 

in your power tool. 

Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. 

Always store your power tool in a dry place. Keep the motor ventilation slots clean. 

Keep all working controls free of dust. 

Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your 

power tool.                                  

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly 

qualified persons in order to avoid a hazard.

TROUBLESHOOTING

1.   If your power tool does not start, check the plug on the power supply first.

2.   If the drill doesn’t work properly, check the drill bit for sharpness, replace drill bit if worn. Check that 

the drill is set to forward rotation for normal use.

3.  If a fault can not be rectified, return the tool to an authorized dealer for repair.

Summary of Contents for PDI750G

















Reviews: