background image

Visit our website at: http://www.harborfreight.com

email our technical support at: [email protected]

For Best results, 

use 3.0 amp Hour Battery 

or Greater

cut-Off Wheel, Battery and 

charger Sold Separately

Owner’s Manual & Safety Instructions

Save This Manual

Keep this manual for the safety warnings and precautions, assembly, 

operating, inspection, maintenance and cleaning procedures.  Write the product’s serial number in the back 

of the manual (or month and year of purchase if product has no number). Keep this manual and the receipt 

in a safe and dry place for future reference.

 22f

When unpacking, make sure that the product is intact 

and undamaged.  If any parts are missing or broken, 

please call 1‑888‑866‑5797 as soon as possible.

Copyright

©

 2022 by Harbor Freight Tools

®

.  All rights reserved.  

No portion of this manual or any artwork contained herein may be reproduced in 

any shape or form without the express written consent of Harbor Freight Tools.  

Diagrams within this manual may not be drawn proportionally.  Due to continuing 

improvements, actual product may differ slightly from the product described herein.  

Tools required for assembly and service may not be included.

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

Summary of Contents for 2269C-B

















Reviews: