background image

13

14

T

ROUBLE SHOOTING THE SYSTEM

We have put together this trouble-shooting guide if you experience problems after installing 

the amplifier. Please keep in mind that the majority of problems incurred are caused by 

improper installation and not the equipment itself. In addition, there are many components 

in the system that could cause various signal problems such as inducted electrical noise 

and engine noise.

Before you can properly address the problem, you must first find the component that is 

causing the problem. This will take patience and a process of elimination.

 

LOOK FOR…..       SOLUTION

No Output

 

Blown fuse 

    Replace

 

Bad RCA Cable(s) 

   Replace

 

+12V at power terminal 

   Check connection

 

+12V at remote terminal      

Check connection

 

Grounding point clean and tight 

  Check for ground w/meter

 

Head Unit’s fader not in center position 

 

Set to center position

 

Master & Slave settings     Confirm correct setting

Low Output

 

Check level adjustments     Re-adjust

 

Bad RCA cable(s)     Replace

 

Improper level matching     Re-adjust

 

Master & Slave settings     Confirm correct setting

Engine Noise

 

Grounding points are clean and tight 

 

Check for ground w/meter

 

Ground all components at same point 

 

Ground at same point

 

Try different grounding point 

  Change for better ground

 

Bad RCA cable(s)     Replace

 

Use High Quality shielded RCA cables 

 

Rejects inducted noise

 

Low Vehicle charging system and/or battery   

Fix and/or replace

Red Protection L.E.D. illuminated

 

Speaker short 

    Check speakers connection

       for short circuit

 

Speaker grounding out 

   Make sure speaker wires

       Do not touch chassis 

         ground

 

Impedance too low 

   Check speaker impedance

 

Overheating 

    Check mounting location

       for Adequate air circulation

       speaker impedance too low

Due to continuous improvement of the product the Specifications are subject to change without notice.

BI1750M

BI3000D

Output Power :

1 ohm

1 x 1750W

1 x 3000W

2 ohm

1 x 875W

1 x 1500W

Rated @ 1 ohm

 

1 x 300W

1 x 600W

Frequency Resp.

10Hz - 300Hz

10Hz - 300Hz

S/N Ra o (A-weight)

>90dB

>90dB

THD with 80k 

lter

<.05%

<.05%

Low Input Level

285mV - 6V

285mV - 6V

Crossover Freq.

40Hz - 300Hz

30Hz - 250Hz

Crossover Slope

12dB

12dB

Bass EQ

12dB @ 45Hz

18dB @ 45Hz

Subsonic Filter

10Hz  - 40Hz

20Hz  - 50Hz

Bass Remote Capability

Yes ( Included)

Yes (Included)

Input Voltage

11.2V - 14.4V

11.2V - 14.4V

BI4500.4

BI4800.4

Output Power :

4 ohm

4 x 75W

4 x 200W

2 ohm

4 x 150W

4 x 400W

Bridged @ 4 ohm

2 x 350W

2 x 800W

Rated @ 4 ohm

2 x 45W

4 x 75W

Frequency Resp.

10Hz - 25KHz

10Hz - 25KHz

S/N Ra o (A-weight)

>90dB

>90dB

THD with 80k 

lter

<.05%

<.05%

Low Input Level

285mV - 6V

285mV - 6V

Crossover Freq. (Low)

50Hz - 250Hz

50Hz - 250Hz

Crossover Freq. (High)

120Hz - 3KHz

120Hz - 3KHz

Crossover Slope

12dB

12dB

Bass EQ

0dB- 12dB @ 45Hz

0dB- 12dB @ 45Hz

Input Voltage

11.2V - 14.4V

11.2V - 14.4V

Summary of Contents for BI4500.4









Reviews: