Basler BE1-DFPR Instruction Manual Download | Manualshive

Page: 115 / 135

background image

BE1-DFPR Testing

5-15

Step 4.

From the Review/Edit Settings Menu, select 1, 4, 7, H, or K to enter the Relay Settings screen for
the desired settings group.

Step 5.

Enter S for the 51P CURV and 51N CURV settings and enter 0 for 51P TD and 51N TD settings.
Press ESC to save these settings, then press ESC again to return to the Review/Edit Settings
menu. This will give a fast trip time for the 51P and 51N elements so the pickup can be checked
accurately.

Step 6.

Connect a current source to any phase current input or the neutral current input.

Step 7.

Close the breaker on the test set and wait for the RST LED to illuminate on the relay.

Step 8.

Slowly ramp up the current. When the relay trips the current being applied should be within ±2%
or 50 ma of the 51P PU setting or 51N PU setting as displayed in the Relay Settings screen.

Step 9.

Return to the Relay Settings screen and return the 51P CURV, 51N CURV, 51P TD and 51N TD
settings to the desired values. Press ESC to save the settings, then press ESC again to return
to the Review/Edit Settings menu.

Step 10. Return to the Tripping Logic screen and return the Trip 1 settings to the desired values. Press

ESC to save the settings, then press ESC again to return to the Review/Edit Settings menu.

50 Pickup

Step 11. From the Review/Edit Settings Menu on the terminal, select 2, 5, 8, I, or L to enter the Tripping

Logic screen for the desired settings group.

Step 12. Enter a N in all Trip 1 locations except 50P and 50N. Enter a Y in the 50P and 50N locations.

Press ESC to save these settings, then press ESC again to return to the Review/Edit Settings
menu. This disables all other functions from tripping the relay so just the 50 function can be
checked.

Step 13. Connect a current source to any phase current input or the neutral current input.

Step 14. Close the breaker on the test set and wait for the RST LED to illuminate on the relay.

Step 15. Slowly ramp up the current. When the relay trips the current being applied should be within ±5%

of the 50P PU setting or 50N PU setting as displayed in the Relay Settings screen.

Step 16. Return to the Normal Mode Tripping Logic screen and return the Trip 1 settings to the desired

values. Press ESC to save the settings, then press ESC again to return to the Review/Edit
Settings menu.

50T Pickup

Step 17. From the Review/Edit Settings Menu on the terminal, select 2, 5, 8, I, or L to enter the Tripping

Logic screen for the desired settings group.

Step 18. Enter a N in all Trip 1 locations except 50TP and 50TN. Enter a Y in the 50TP and 50TN

locations. Press ESC to save these settings, then press ESC again to return to the Review/Edit
Settings menu. This disables all other functions from tripping the relay so just the 50T function
can be checked.

Step 19. From the Review/Edit Settings Menu on the terminal, select 1, 4, 7, H, or K to enter the Relay

Settings screen for the desired settings group.

«
...
113
114
115
116
117
...
»

Summary of Contents for BE1-DFPR








































































































































Reviews:

No comments

Related manuals for BE1-DFPR

Z-one ZSR101 Series

Brand: CALEFFI Pages: 52

Brand: SymCom Pages: 4

Brand: ABB Pages: 24

Circuit Shield 87B

Brand: ABB Pages: 15

Brand: ABB Pages: 12

HR1S-DMB Series

Brand: IDEC Pages: 16

Brand: Siemens Pages: 25

Brand: Sonoff Pages: 52

Brand: Taco Comfort Solutions Pages: 2

Brand: TE Connectivity Pages: 2

Agile P50 Series

Brand: GE Pages: 268

Brand: GE Pages: 24

Ex STM 295 3G/D Series

Brand: steute Pages: 24

Brand: System Sensor Pages: 2

RadioLink ScenePoint RDR1 Series

Brand: Vantage Hearth Pages: 4

360 comfort RE153 Series

Brand: Stelpro Pages: 2

Brand: Vimar Pages: 8

Brand: KinCony Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands