background image

- 2 -

IMPORTANT SAFETY NOTICE

• ADULT SUPERVISION IS REQUIRED DURING THE ASSEMBLING AND THE 

INSTALLATION OF THE PROBASE. 

• MISUSE OF A SLEDGEHAMMER CAN RESULT IN SERIOUS INJURY.
• ALWAYS WEAR SAFETY GOGGLES WHEN USING THE SLEDGEHAMMER.
• ENSURE THAT THERE IS ENOUGH ROOM AROUND YOU SO THAT YOU 

CAN SWING THE HAMMER FREELY. 

• MAKE SURE PEOPLE ARE AT LEAST 12 FEET AWAY WHILE USING THE 

SLEDGEHAMMER.

WARNING

Before using this product, please read the following carefully:

Your PROBASE and your portable basketball hoop MUST be assembled and installed 
according to the instructions. Failure to comply with the instructions may result in SERIOUS 
INJURY.

PROBASE Inc. is not responsible for any health or safety concerns or any material 
breakdown once the buyer has installed the PROBASE. If any harm or material 
breakage is incurred, the user accepts all responsibility. 

Once your portable hoop is installed in the PROBASE, NEVER hang on its rim, on its 
net or on any other part of your equipment, including the backboard and its support 
braces. 

Check the stability of the system before each use. 

Check the condition of the PROBASE before each use (loose screws, excessive wear, 
signs of corrosion and steel distortion)

Tighten, adjust or replace defective components before each use.

Do not use the PROBASE system on days of strong winds and/or storms.   

Summary of Contents for probase01














Reviews: