Version 08/13
Hydraulic Shunting Jack
Item no. 82 36 11
1. Intended use
This hydraulic jack lifts loads with a weight of up to 2 t. The saddle can be rotated by 360 º and thereby guaranteeing an optimal
adaptation to different circumstances. The working height of the device is 135 to 207 mm and can be used with the dual pump
lever set.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product for purposes other
than those described above, the product may be damaged. In addition, improper use can cause hazards such as short circuiting,
¿
re, electric shock etc. Read the instructions carefully and keep them. Make this product available to third parties only together
with its operating instructions.
This product complies with the statutory national and European requirements. All company names and product names are
trademarks of their respective owners. All rights reserved.
2. Delivery content
• Hydraulic shunting jack
• Handle
• Operating
instructions
3. Safety instructions
Read the operating instructions carefully and especially observe the safety information. If you do not
follow the safety instructions and information on proper handling in this manual, we assume no liability
for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.
Warning
This is a lifting device only. Load must be supported by proper rated capacity jack stands under the
vehicle before starting inspection or work.
Do not overload, jack lifting capacity is 2 tons.
Overloading can cause damage to jack and/or failure resulting in personal injury or property damage.
This jack is designed for use on hard level surfaces, use on other than hard surfaces can result in jack
instability and possible loss of load.
Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
À
ammable gases,
vapours and solvents.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. Safe
operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
• Do not overload! Jack capacity is 2 tons.
• All movable parts must be kept clean and been greasy regularly.
• Oil should stand always up to the lower edge of the oil egg
¿
lling stopper. Do not use brake oil!
• The device is not a toy and should be kept out of reach of children!
• At work under the vehicle, the vehicle should be secured by suitable brake blocks.
• Pay attention to the fact that nobody leans against the vehicle if the vehicle is raised.
• Wheels should be blocked and the hand brake be pulled.
Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance,
modi
¿
cations and repairs are to be performed exclusively by an expert or at a quali
¿
ed shop.
• If you have questions which remain unanswered by these operating instructions, contact our technical support service or
other technical personnel.
4. Operating elements
1. Power unit
2. Snap ring “C”
3. Brass shaft
4. Auxiliary shaft
5. Frame (L) Unit
6. Washer
7. Nut
8. Nut
9. Spring washer
10. Washer
11. Steel ball
12. Castor unit
13. Middle shaft
14. Collar
15. Front wheel
16. Front wheel shaft
17. Frame (R) unit
18. Lifting arm unit
19. Lifting arm shaft
20. Wire pin
21. Saddle unit
22. Cover plate
23. Return spring
24. Piston rod shaft
25. Handle
26. Pin
27. Spacer
28. Carrying handle
5. Operation
It is necessary that the operator can watch the lifting device and the load during all movements.
The operator shall be provided with all necessary information about training and about pumping and
translating forces.
To avoid overloading the hydraulic jack, this is equipped with a boiler safety valve. This is put by the manufacturer and may be
shifted by no means.
Lifting
1. Prevent the vehicle from rolling away by using brake pads and the handbrake.
2. Turn the valve lifter of the mechanism clockwise (to the right) until it stops. Insert the handle into the hole (small bolt must
face upwards).
3. Pump up the jack and make sure that the saddle is correctly placed under the vehicle (only at designated places).
Place the hydraulic jack in a way that you do not reach under the vehicle. Do not place the hydraulic jack at an
angle.
Lowering
Turn the valve of the lifting mechanism carefully counter-clockwise (to the left).
The pressure decreases and the siphon lowers.
6. Disposal
At the end of its service life, dispose of the product according to the relevant statutory regulations.
<
ou thus ful
¿
l your statutory obligations and contribute to the protection of the environment.
7. Technical data
Load capacity:
2 t
Lifting range:
135 - 325 mm
Dimensions (W x H x D):
200 x 135 x 471 mm
8. Declaration of Conformity
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare on our own responsibility that the product:
Basetech
ZQ20002
is in conformity with the following directive and norms:
2006/42/EG
EN 1494: 2000 +A1: 2008
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, micro
¿
lming, or the capture in electronic
data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
The operating instructions re
À
ect the current technical speci
¿
cations at time of print.
We reserve the right to change the technical or physical speci
¿
cations.
© 2013 by Conrad Electronic SE.
V2_0813_02-HK
