• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
Installation
Any modifications to the vehicle required due to the installation of the lamp
must be performed in such a way that they do not affect traffic safety or
constructional stability of the vehicle. If you have any doubts regarding the
installation location, contact your car dealer.
Make sure that cables, brake lines, the fuel tank, etc. can not be damaged
before completing the fixing holes.
When using tools for installation, always observe the safety instructions
provided by the tool manufacturer.
When installing the lamp, consider any potential risks of accidents that can
arise due to devices loosening in case of an accident. Securely mount the
lamp at a location where it does not pose any risk for passengers.
ON
OFF
3mm
Connecting the power supply
Only experts may perform electrical connections. While doing so, disconnect
the negative terminal (ground) of the on-board battery in order to avoid short
circuits and any consequent damage to the device.
Only reconnect the negative battery terminal, after you have connected the
lamp completely and checked all connections. Only use a voltmeter or a
diode test lamp to check the voltage at the on-board voltage lines since
normal test lamps consume excessive currents and can damage the on-
board electronics.
Route cables in such a way that they do not get jammed or touch sharp
edges. Use rubber grommets at points of passage.
RED
WHITE
Operating instructions
Version 08/15
Interior LED light
3 W
Item no. 1362526
4 W
Item no. 1362527
Intended use
The interior LED light is intended for use as light source inside vehicles.
Only use inside vehicles or other enclosed areas. Do not use outdoors. Avoid contact with
humidity or moisture. When installing the lamp, make sure it is protected against humidity and
moisture.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you
use the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Interior LED light
• 3 x screws
• Operating instructions
Explanation of symbols
This symbol indicates a health hazard, e.g. electric shock.
The exclamation mark indicates specific risks associated with handling, function and
use.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly or
- has been stored for extended periods in poor ambient conditions.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Check the device before start-up for any damage. It may not be put into operation
in the case of damage.
• The LED illuminants are fixed and cannot be replaced.
• Attention, LED light: Do not look directly into the LED light! Do not look into the
beam directly or with optical instruments!
• The product is only intended for connection to a 12 V/DC on-board supply system
with the negative terminal of the battery fitted to the car body and must only be
installed and operated in vehicles with such on-board supply system. Never
connect the lamp to another voltage supply.
