background image

 

 

 

 

- 16 - 

2. Safety 

 

This section provides an overview of all important safety aspects. 

In addition every chapter provides precise safety advice for the prevention of dangers 
which are highlighted by the use of the above mentioned symbols.  

Furthermore, attention should be paid to all pictograms, markers and labels on the 
device, which must be kept in a permanent state of legibility. 

By following all the important safety advice you gain an optimal protection against all 
hazards as well as the assurance of a safe and trouble-free operation. 

 
 

2.1 General Information 

 

This device is designed in accordance with the presently applicable technological 
standards. However, the device can pose a danger if handled improperly and 
inappropriately. 

Knowing the contents of the instruction manual as well as avoiding mistakes and thus 
operating this device safely and in a fault-free manner is very essential to protect 
yourselves from the hazards. 

To prevent hazards and to ensure optimum efficiency, no modifications or alterations to 
the device that are not explicitly approved by the manufacturer may be undertaken. 
This device may only be operated in technically proper and safe condition. 

 
 

2.2 Safety instructions for use of the device 

 

The specifications regarding the industrial safety are based on the Regulations of the 
European Union applicable at the time of manufacturing the device.  

If the device is used commercially, the user is obliged to ensure that the said industrial 
safety measures concur with the state of the rules and regulations applicable at the time 
in question for the entire period of use of the device and to comply with the new 
specifications.  

Outside the European Union, the industrial safety laws applicable at the place of 
installation of the device and the regional territorial provisions must be complied with. 

Besides the industrial safety instructions in the instruction manual, the general safety and 
accident prevention regulations as well as environment protection regulations applicable 
for area of application of the device must be followed and complied with. 

 

Summary of Contents for 104.446














Reviews: