Bartell BM90, Owner'S Manual And Parts Book

Page: 16 / 26

WALK BEHIND POWER TROWEL INSTRUCTION MANUAL
The trowel arm adjustment fixture (20801) is reversible.
By rotating the arm clamping fixture and the ring bolt,
both left hand and right hand trowel arms may be
adjusted. Before attempting adjustment, determine
whether the trowel arm is right handed or left handed.
When adjusting left hand trowel arms use the side of the
fixture marked “L”. When adjusting right hand trowels
arms use the opposite side. The adjustment bar will be
set on “36” for the Walk-behind trowel arm.
ADJUSTMENT PROCEDURE
1. Remove all trowel arm assemblies (1 & 2 arm and
attached lift lever) from suspected maladjusted spider
plate.
2. Remove lift lever (2) from trowel arm (1) by first
loosening jam nut (3) then square head screw (4). If
upon inspection (method left to discretion of
serviceman) any trowel arm (1) is found to be in a
bent condition, it must either be brought back to its
original straight condition (method left to the
serviceman’s discretion) or replaced with new part.
3. Replace lift levers (2) on new or straightened arms
(1) by reversing procedure as described above.
4. Place trowel arm assembly (1 and 2) in fixture (5)
with lift lever (2) butting up against fixture. Clamp in
place with bolts (6).
5. Loosen locknut (7) and screw carriage bolt (8) down
to full depth allowable. This will provide for ample
clearance to swing precision ground adjustment bar
(9) over head of carriage bolt.
Adjustment bar (9) is stamped for appropriate size of
machine. Swing appropriate side directly over carriage
bolt (8) and secure in place with bolt (10).
6. Adjust carriage bolt (8) upwards until contact is made
with adjustment bar (9); holding carriage bolt in
position with one wrench, tighten locknut (7) to secure
in position with second wrench.
7. This same procedure is to be followed with ALL arms
from spider plate assembly, and will ensure correct
and exact adjustment.
TROWEL ARM ADJUSTMENT SCREW
The trowel arm adjustment screw is to be used for field
adjustment of blade level, in the event of a damaged
trowel arm, to enable completion of the job. At the end of
the job repairs should be made to eliminate the damage.
When assembling trowel blades to trowel arms, the
adjustment screw should NEVER protrude below the
under-side surface of a trowel arm.
If the adjustment screw is not flush with the underside of
the trowel arm, then this will cause the power trowel to
bounce and vibrate especially at high speed. This will
also cause the trowel blades to leave an uneven finish to
the concrete due to the blades not being level to one
another.
Make certain that the adjusting screw is held firmly in
place while tightening the bolt which secures the blade to
the trowel arm.
17
375 ANNAGEM BLVD., MISSISSAUGA, ONTARIO, CANADA L5T 3A7, 905-364-4200 FAX 905-364-4201
CREATED: 07/04
REVISED: 05/10
TROWEL ARM ADJUSTMENT FIXTURE
PART #20801
Ex: Unit 36” (B436)
1) 10810A – Trowel arm
2) 10817A – Lift lever
3) 10808 – Jam nut
4) 10809 – Set screw
5) 10824 – Block top
6) 10507 – Bolt
7) 10808 – Jam nut
8) 10807 – Carriage bolt
9) 10832 – Adjustment bar
10) 10507 – Bolt
Figure 5a.
NOTE: IT IS IMPORTANT THAT WHEN TIGHT -
ENING SQUARE HEAD NUT (4), IT SEATS ITSELF
SECURELY INTO DIMPLE MACHINED IN ARM.
NOTE: IT IS VITALLY IMPO RTANT TO ENSURE
THAT ONCE THE CARRIAGE BOLT IS ADJUSTED
TO THE CORRECT HEIGHT, IT DOES NOT MOVE
BEFORE, OR DURING THE TIGHTENING OF
LOCKNUT.
CREATED: 06/12
HANDLE ASSEMBLY (BM90/BM436)
15
Part Number Description Qty. Part Number Description Qty.
21703 Handle Welding Part 1 11802 Nut 6
21729 Safety Switch Assembly 1 10889 Screw 4
21702 Upper Joint Plate 1 13350 Screw 1
21701 Lower Joint Plate 1 10703 Lock Washer 1
10508 Throttle Control Assembly 1 21708 Pin 1
21707 Handle Wheel 1 21709 Bearing 1
21731 Bushing 1 21726 Screw 1
21713 Adjust Shaft 1 21712 Ext. Circlip 1
21711 Washer 1 21725 Bolt 1
21715 Adjust Shaft Bushing 1 21724 Pin 1
21705 Pulley 1 21706 Pin 1
10923 Yoke Arm Shaft 1 50266 Wave Washer 1
10312 Yoke Arm 1 10922 Retaining Ring 2
21704 Wheel Bushing 1 21717 Plastic Handle 2
21716 Pitch Control Cable 1
21707
21709
21731
50266
21711
21712
21713
21708
21726
10703
21725
21715
21717
21703
10894
21729
21724
21716
21702
21706
10312
11802
10923
21705
10922
21704
10889
13350
11802
21701
10508