background image

RIDE-ON FAMILY 

 

OWNER’S MANUAL 

 

24 

 

OIPB 

– B19007

 

TROWEL ARM ADJUSTMENT FIXTURE 

 
Part #20801 
Unit 36” (TS88, BXR836, TS78,  
All Titans) 
1) 10411 

– Trowel arm 

2) 10817 

– Lift lever 

3) 10808 

– Jam nut 

4) 10809 

– Set screw 

5) 10824 

– Block top 

6) 10507 

– Bolt

 

 

7) 10816 

– Jam nut 

8) 10815 

– Carriage bolt 

9) 10832 

– Adjustment bar 

10) 10507 

– Bolt 

 
Part #20801 
Unit 46” (TS96)  
1) 14161 

– Trowel arm  

2) 14163 

– Lift lever  

3) 10808 

– Jam nut  

4) 10809 

– Set screw  

5) 10824 

– Block top  

6) 10507 

– Bolt  

7) 10905 

– Washer  

8) 10807 

– Carriage bolt  

9) 10832 

– Adjustment bar  

10) 10507 

– Bolt  

 
 

The trowel arm adjustment fixture (20801) is reversible. By rotating the arm clamping 

fixture and the ring bolt, both left hand and right-hand trowel arms may be adjusted. Before 
attempting adjustment, determine whether the trowel arm is right handed or left handed. When 
adjusting left hand trowel arms use the side of the fixture marked “L”. When adjusting right hand 
trowels arms use the opposite side.  

ADJUSTMENT PROCEDURE 

1.  Remove all trowel arm assemblies (1 & 2 arm and attached lift lever) from spider plate. 
2.  Remove lift lever (2) from trowel arm (1) by first loosening jam nut (3) then square head 

screw (4). If upon inspection (method left to discretion of serviceman) any trowel arm (1) 
is found to be in a bent condition, it must either be brought back to its original straight 
condition (method left to the serviceman’s discretion) or replaced with new part. 

3.  Replace lift levers (2) on new or straightened arms (1) by reversing procedure described 

above. 

 

4.  Place trowel arm assembly (1 and 2) in fixture (5) with lift lever (2) butting up against 

fixture. Secure in place with bolts (6). 

5.  Loosen locknut (7) and screw carriage bolt (8) down to full depth allowable. This will 

provide for ample clearance to swing adjustment bar (9) over head of carriage bolt. 
Adjustment bar (9) is stamped for appropriate size of machine. Swing appropriate side 
directly over carriage bolt (8) and secure in place with bolt (10). 

NOTE: It is important that when tightening square head setscrew (4), it seats itself 
securely into dimple machined arm. 

Summary of Contents for BXR-836





























Reviews:

Related manuals for BXR-836