background image

Maintenance, Continued

Routine Battery Inspection and Maintenance

Sealed Lead-Calcium Batteries

Maintenance-free cells are the most common type of battery used today in standby equipment. By design, it is as 

maintenance-free as a battery can be. It is recommended, however, that some simple steps be taken to increase system 

life and maximize reliability:

1. A quarterly visual check of the battery should be conducted to look for deformities in the battery case, electrolyte 

leakage, and/or terminal corrosion. Any batteries with these conditions are defective and should be replaced. Any 

corroded terminals found, regardless how slight, are to be cleaned at once to prevent system failure.

2. Once a year, all battery connections should be checked for tightness and cleaned and retightened, as necessary.

Battery Replacement Procedure

WARNINGS:

• Always use the same quantity and type of battery as replacements.

• Substituting batteries not supplied by the Manufacturer will void the UL listing of the system and may cause equipment 

failure. To ensure the superior performance of your 

Tucson Micro 

inverter system and to maintain proper charger 

operation, replace spent batteries only with those having the same part number, voltage, and ampere-hour rating as the 

original batteries.

1. Follow the proper shut down procedure as described in the 

Maintenance - Safe Shut Down Procedure

 section on 

page 11.

2. Disconnect the battery Positive red (B+) and Negative black (B-) connectors.

3. Remove the battery from the cabinet.

4. Install the new battery following the instructions outlined in the 

Battery Information - Battery Installation and 

Connection

 section on page 9.

Battery Disposal

WARNINGS:

• Do not dispose of batteries in a fire; the batteries could explode.

• Do not open or mutilate batteries.

• Released electrolyte is highly toxic and harmful to the skin and eyes.

CAUTION:

 Batteries contain lead or cadmium, depending on model. Many state and local governments have regulations 

about used battery disposal. Please dispose of the batteries properly.

 

Tucson Micro Series

Installation Instructions

10070249 

R

EV 1 - 06/21

12

800-533-3948 www.barronltg.com

Summary of Contents for EXITRONIX Tucson Micro Series














Reviews: