Barrett 2030 Operating And Installation Manual Download Page 56

Page: 56 / 208

BARRETT 2030 HF SSB TRANSCEIVER

Mute (Squelch) Selection

There are three mute (squelch) modes:-

Audio (syllabic) mute (squelch) – the receiver audio is enabled when speech
is detected on the selected channel.

Note:-

The syllabic mute sensitivity can be set to three levels, these levels can be

set either when programming the transceiver or in the

“Mute Settings”

section of

the protected menu.

Selective Call mute (squelch)

– the receiver audio is enabled after a Selcall sent

to the unit has been received and decoded successfully

Signal Strength Level (SSL) mute (squelch)

– the receiver audio is enabled when

the received signal strength exceeds the nominated threshold level.

Note:-

The signal strength mute level can be set to three levels, these levels can

be set either when programming the transceiver or in the

“Mute Settings”

section

of the protected menu.

The current mute (squelch) state is displayed the first time the mute key

pressed.

To change the mute state, while the mute state is still displayed from the first press
of the mute key, press the mute key again to scroll through to the required mute
state.

press

the

key

press

the

key

56 of 208

Summary of Contents for 2030

















































































































































































































Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands

Barrett 2030, Operating And Installation Manual

Search results

Summary of Contents for 2030

Reviews:

Related manuals for 2030

Brands by name

Popular brands