manualshive.com logo in svg

Barreto E13SGH, Operator'S Manual, Page: 9 / 18

Share
Download
Barreto E13SGH Operator'S Manual Download Page 9

16SG OPERATOR’S MANUAL                   REVISED  2/16/17                           Page 9 of 18 

 
 

 
 

                                             ENGINE CONTROLS 

 

FUEL SHUTOFF VALVE: Must be in OPEN position for engine to run. 

 

CHOKE: Use while starting the engine, only needed if engine has not reached operating temperature.  

(Refer to the ENGINE START UP PROCEDURE) 

 

THROTTLE: Controls engine speed. Operate at full throttle when cutting (all the way forward). 

                        

 

ENGINE START UP PROCEDURE 

 

Only operate machine outdoors and avoid breathing engine exhaust and fumes.  

WARNING

: Engine exhaust contains carbon monoxide gas that is toxic. Breathing it can cause 

unconsciousness and death. Avoid any areas or actions that expose you to carbon monoxide.  

 

 

COLD WEATHER OPERATIONS: Before operating in cold weather, refer to the Engine Owner’s Manual 

for recommended engine oil. Do not spray starting fluid into the air cleaner as engine damage could result. 

 

Engine bail switch must be held down for engine to start and run. If the bail switch is released, the engine 

will shut down.  

 

 

  

Summary of Contents for E13SGH



















Reviews:

No comments