background image

2

PARTS LIST

WARNING: DO NOT

 use while under the influence of alcohol or drugs (prescription or non-prescription) as 

these may impair user’s ability to properly assemble or safely operate the appliance.
Avoid contacting moving parts. Wait until all parts have come to a complete stop and disconnect from the 

power source before removing any parts of the grinder.

WARNING: NEVER 

feed food into grinder by hand as serious injury may occur, always use provided meat

stomper. 

DO NOT

 use fingers to scrape food away from the grinding plate while the grinder is running.

Thoroughly hand-wash all grinder parts in warm soapy water prior to use. 

DO NOT

 soak. This product is 

NOT DISHWASHER SAFE

 (discoloration may occur)

Tie back loose hair and clothing. Remove neckties, rings, watches, bracelets or other jewelry before  

operating the grinder.

DO NOT

 run grinder without meat in the Grinder Head, severe damage to the Grinder Head and Auger  

could result.
Use grinder on a level, stable surface to prevent tipping. 

NEVER

 move the grinder while unit is in use.

WARNING:

 Knife and plates are SHARP! To avoid injury, use extreme caution when handling. 

If your unit fails to operate, contact Barton for technical assistance at 909.628.0880. If meat is mashing 

instead of extruding in strings from the grinding plate, chill the meat  to 40˚, and check to see that the plate 

and knife are properly installed. A dull knife or plate will  also cause mashing of the meat. 

To protect against risk of electrical shock, 

DO NOT 

put appliance in water or any other liquids

DO NOT

 place this appliance on or near gas or electric burners or stoves. 

DO NOT

 place this appliance 

inside or on top of a heated conventional oven, microwave oven, or other heat source or a dishwasher. 

DO NOT

 submerse or expose the electrical components of this product to water or any other liquids.

WARNING:

 The cutting blade is sharp; always handle with care when using and while cleaning. 

CAUTION: NEVER PUT YOUR FINGERS NEAR THE FOOD CHUTE WHILE GRINDER IS IN OPERATION.

To avoid a circuit overload, do not operate another electrical product on the same electrical circuit as this 

product. 

Disconnect the plug (

DO NOT

 pull on Power Cord) from the electrical outlet. 

DO NOT

 put any stress on 

the Power Cord where it connects to the product, as the Power Cord could fray and break. 

NEVER

 operate this appliance if it has a damaged Power Cord or plug, is not working properly, has been 

dropped or damaged in any manner, or the Power Cord or Handle has been exposed to water or any other 

liquids. 

DO NOT

 attempt to examine or repair this product yourself. 

DO NOT

 use any abrasive cleaning agents or cleaning cloths or sponges when cleaning the appliance. 

yourself. 

DO NOT

 use fingers to scrape food away from the cutting blade while appliance is in operation as injury 

may result. 

Only use this unit when it is completely and properly assembled. 
Longer power-supply cords or extension cords are available and may be used if care is exercised in their 

use. If an extension cord is used: (1) the marked electrical rating of the extension cord should be at least 

as great as the electrical rating of the product.

Summary of Contents for 90800









Reviews: